background image

INSTALLATION

To install the handles onto the front panel of the repeater,
align the handles with the holes on the front panel, then
secure the handles using the supplied screws.

Please consult your dealer for installing the repeater and
antenna.

MICROPHONE

Connect an optional KMC-27A, KMC-27B, or KMC-9C

KENWOOD

 microphone to the 

MICROPHONE

 jack on

the front panel.

VHF FM REPEATER/ UHF FM REPEATER

TKR-740/ TKR-840

INSTRUCTION MANUAL

KENWOOD CORPORATION

© B62-1136-00 (K)

09 08 07 06 05 04 03 02 01 00

NOTICES TO THE USER

UNPACKING AND CHECKING EQUIPMENT

Note:

  The following unpacking information is for use by your 

KENWOOD

dealer, an authorized 

KENWOOD

 service facility, or the factory.

Carefully unpack the repeater.  We recommend that you
identify the items listed in the following table before
discarding the packing material.  If any items are missing
or have been damaged during shipment, file a claim with
the carrier immediately.

If you detect an abnormal odor or smoke coming from the unit,
disconnect the power from the unit immediately.  Contact your

KENWOOD

 service center or dealer.

FCC WARNING

This equipment generates or uses radio frequency energy.  Changes or
modifications to this equipment may cause harmful interference unless
the modifications are expressly approved in the instruction manual.  The
user could lose the authority to operate this equipment if an unauthorized
change or modification is made.

GOVERNMENT LAW PROHIBITS THE OPERATION OF
UNLICENSED RADIO TRANSMITTERS WITHIN THE
TERRITORIES UNDER GOVERNMENT CONTROL.

ILLEGAL OPERATION IS PUNISHABLE BY FINE OR
IMPRISONMENT OR BOTH.

REFER SERVICE TO QUALIFIED TECHNICIANS ONLY.

m

e

t

I

r

e

b

m

u

N

t

r

a

P

y

t

i

t

n

a

u

Q

s

s

a

l

g

t

n

o

r

F

4

X

-

0

9

5

2

-

0

1

B

1

)

A

4

(

e

s

u

F

5

X

-

7

2

0

4

-

6

0

F

1

t

e

s

w

e

r

c

s

d

n

a

s

e

l

d

n

a

H

5

X

-

1

2

4

0

-

1

0

K

1

y

l

b

m

e

s

s

a

e

l

b

a

c

r

e

w

o

P

5

X

-

1

1

7

0

-

7

3

E

1

)

n

i

p

5

1

(

r

o

t

c

e

n

n

o

c

h

t

i

w

e

r

i

w

d

a

e

L

5

X

-

8

2

2

3

-

1

3

E

1

)

n

i

p

2

1

(

g

u

l

p

e

r

a

u

q

S

5

X

-

0

1

4

0

-

9

5

E

1

w

e

r

c

s

d

e

s

s

e

r

D

4

X

-

3

4

5

0

-

8

0

N

1

l

a

u

n

a

m

n

o

i

t

c

u

r

t

s

n

I

X

X

-

6

3

1

1

-

2

6

B

1

THANK YOU!

We are grateful you purchased this 

KENWOOD

 repeater.

We believe this easy-to-program repeater will be highly
effective in your communications system, and will keep
personnel operating at peak efficiency.

KENWOOD

 incorporates the latest in advanced

technology into all of our products.  As a result, we feel
strongly that you will be pleased with the quality and
features of this product.

FEATURES

You can easily program channel data using the KPG-47D
version 2.00 or later (optional) on a PC.

You can recall 1 of 32 preset channels using either a PF key or
the external control line.

The firmware can be written to the Flash memory through an
external source.

QT/DQT signalling can be programmed on each channel. It
simultaneously decodes up to 16 different QT/DQT tones.

When using the KPG-47D version 2.00 or later (optional), RX
PLL lock voltage, RX input signal strength, TX PLL lock voltage,
TX output power, and the power supply voltage can be
monitored on a PC.

The interface port can be used with external equipment, such
as a repeater controller.

The repeater has multi-mode capability.
Wide: 30 kHz, 25 kHz/ Narrow: 15 kHz,12.5 kHz (TKR-740)
Wide: 25 kHz/

Narrow: 12.5 kHz

(TKR-840)

You can adjust the following functions from a PC:

CW ID Deviation

Digital Pager Balance

Digital Pager Deviation

DQT Deviation

Maximum Deviation

QT Deviation

Remote TA

Repeat Gain Level

TX Power

RX Audio Signal Output (RA)

RX Detector Signal Output (RD)

Signalling Balance

Signalling Deviation (SD)

Squelch (Analog/ RSSI)

Test Tone Deviation

TX Audio Input (TA)

Voting Tone Level

PRECAUTIONS

Do not expose the unit to rain or moisture; to prevent fire or
electric shock.

Do not open the unit under any circumstances; to avoid risk of
electric shock.

Do not expose the unit to long periods of direct sunlight, nor
place it close to heating appliances.

Do not place the unit in excessively dusty and/or humid areas,
nor on unstable surfaces.

Reviews: