background image

KENWOOD CORPORATION

 

                 

TK-2170-K, TK-2170-K2    FCC ID:ALH34703110 / IC:282D-34703110 

TK-3170-K, TK-3170-K4, TK-3173-K    FCC ID:ALH34713110 / IC:282D-34713110 

TK-3170-K3, TK-3170-K6    FCC ID:ALH34713130 / IC:282D-34713130 

 

 

 

INSTRUCTION MANUAL 

TK-2170/TK-3170/TK-3173 

THANK YOU!

 

We are grateful you chose 

KENWOOD 

for your land mobile radio applications. We believe this easy-to-use transceiver 

will provide dependable communications to keep personnel operating at peak efficiency. 

KENWOOD 

transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be 

pleased with the quality and features of this product. 

 

NOTICES TO THE USER 

WARNING: 

• GOVERNMENT LAW PROHIBITS THE OPERATION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE 
TERRITORIES UNDER GOVERNMENT CONTROL. 
• ILLEGAL OPERATION IS PUNISHABLE BY FINE OR IMPRISONMENT OR BOTH. 
• REFER SERVICE TO QUALIFIED TECHNICIANS ONLY. 
• DO NOT OPERATE YOUR TRANSCEIVER IN EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, ETC.). 
• TURN OFF YOUR TRANSCEIVER WHILE TAKING ON FUEL, OR WHILE PARKED IN GASOLINE SERVICE 
STATIONS. 

 

SAFETY:

   

It is important that the operator is aware of and understands hazards common to the operation of any transceiver. 
 

WARNING: 

EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) 
Turn off your transceiver while taking on fuel, or while parked in gasoline service stations. 
 

One or more of the following statements may be applicable: 

 

FCC WARNING 

This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause 
harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the 
authority to operate this equipment if an unauthorized change or modification is made. 
 

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of 
the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference in a residential installation. 
This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance 
with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, 
the user is encouraged to try to correct the interference by one or more of the following measures: 
• Reorient or relocate the receiving antenna. 
• Increase the separation between the equipment and receiver. 
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. 
• Consult the dealer for technical assistance. 
 

Summary of Contents for TK-2170-K












Reviews: