Kenmore 625.75116 Use & Care Manual Download

Page: 1 / 26

System tested and certified by NSF

International against NSF/ANSI Standard 44

for hardness reduction, efficiency and the

reduction of barium and radium 226/228,

and certified to NSF/ANSI Standard 372.

Système évalué et certifié par NSF Inter-

national selon la norme NSF/ANSI 44 pour la

réduction de la dureté de l’eau, l’efficacité et

la réduction de baryum et radium 226/228,

et certifié selon la norme NSF/ANSI 372.

P/N 7339939 (Rev. E 5/13/14)

Use & Care Guide

Guide de l’utilisation et d’entretien

English / Français

Model / Modèle 625.75116

Kenmore

Water Softener

with High Flow Valve

Adoucisseur d’eau

avec soupape à haut débit

System tested and certified by the Water

Quality Association against CSA B483.1.

Système évalué et certifié par Water Quality

Association selon la norme CSA B483.1.

USA

Sears Canada Inc.

290 Yonge Street

Toronto, Ontario M5B 2C3 Canada

www.kenmorewater.com

www.kenmore.com

www.sears.ca

Summary of Contents for 625.75116



























Search results

Summary of Contents for 625.75116

Reviews:

Related manuals for 625.75116

Brands by name

Popular brands

Kenmore 625.75116, Use & Care Manual

Search results

Summary of Contents for 625.75116

Reviews:

Related manuals for 625.75116

Brands by name

Popular brands