Kemco 50-0230B-002 Installation Instructions Manual Download | Manualshive

Page: 1 / 8

background image

INSTALLATION INSTRUCTIONS

FOR

50-0230B-002

50-0230B-003

50-0230B-004

SUBURBAN

Overhead console with flip down TV

These instructions are intended for use only by experienced professionals in the automotive
customizing business. Special tools and equipment, as well as specialized handling and care
of product during installation, may be required. Before beginning this installation, carefully read

through the following instructions.

Use extreme care when cutting headliner material.

Check for wiring or other componentry above headliner material. Cut only where indicated.

Materials/ Tools required for this installation:
1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter

3. T-15 TORX bit driver 4. Razor knife or similar
5. T-45 TORX bit driver 6. 1/4” hex socket bit

7. Awl or similar tool 8. 3/32” Drill bit
9. Audiovox Series 645/655 Video Module

KEMCO

INSTALLATION INSTRUCTION # 44-0022B

May 26, 1999
Printed in the U.S.A.

1
2
3
...
»

Summary of Contents for 50-0230B-002









Reviews:

No comments

Related manuals for 50-0230B-002

Brand: Hyundai Pages: 52

Brand: Advanced ICE Pages: 7

Prestige Close Coupled Systems

Brand: Rinnai Pages: 48

Brand: Jensen Pages: 4

Brand: Uniden Pages: 76

Brand: Crestron Pages: 26

NavMate NM-PN600

Brand: Horizon Navigation Pages: 38

Brand: v.link Pages: 18

Brand: Rexing Pages: 18

Brand: Gainward Pages: 2

Brand: Advanced Native Technologies Pages: 29

Brand: Sune Technology Pages: 16

Brand: Sime Pages: 29

Brand: Crutchfield Pages: 14

Brand: Naxa Pages: 1

Brand: Crystal Sound Pages: 2

Brand: RCA Pages: 10

Brand: THOMSON Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands