SyStem deScription
KEETEC TS 10 a car alarm for vehicles with 12V power supply. It is used for sensing
over doors, trunk and hood. Part of the system is a shock sensor, which triggers
an alarm after detection of shocks caused by e.g. breaking of the window. System
breach is signalized with optical (direction lights) and acoustic (siren) signalization.
Immobilizer is armed when the alarm is turned on, which interrupts the ignition circuit
and therefore prohibits unauthorized starting of the vehicle. Car alarm is controlled
by remote control, which also controls central locking.
remote controL deScription
BUttonS FUnctionS deScription
i. FUnctionS
tUrning on the car aLarm
Press button 1 Siren sounds with 1 or not sound. (See programming menu F1).
Directional lights flash 1. Central locking with locks and immobilizer is activated.
After 8 or 40 seconds. (See programming menu F3), the system is active. LED
flashes slowly. All the sensors are active. If a violation occurs the sensor to 8 or 40
seconds, the system automatically skips if not in peace again. If no closed doors or
hood of the vehicle up to 8 or 40 sec., The siren sounds 4.
tUrn oFF the car aLarm
Press button 2 Siren sounds you hear or 2x (see programming menu F1). If you turn
off the car alarm siren sounds 4 times, was triggered by an alarm during a sitting.
Directional lights flash 2 times. If 4x flash was caused by the baby alarm. Central
locking and unlocking the immobilizer is deactivated. LED is off. If the baby during
an alarm, the LED indicates the number of flashes, which caused alarm input:
2 flashes
- an alarm from the additional sensor
3 flashes
- from alarm door contacts
6 flashes
- Alarm triggered by turning the ignition
emergency panic aLarm
Whenever you press buttons simultaneously 1 and 2, the siren will sound and direc-
tional lights will blink for 30 seconds. Pressing 1 or 2 emergency alarm to deactivate it.
VehicLe Search
Car alarm must be turned on. Press button 1 1x Siren sounds and indicator lights flash
10 times. Pressing the 2 button to exit the vehicle and search off car alarms.
KEETEC TS 10
CAR ALARM USER MANUAL
SK
opening the trUnk
Press button 3 Activate output (-300mA) to open the trunk to 0.5 seconds. If the trunk
is open, the system automatically omitted from the entrance door monitoring contact.
After closing the door contacts will be delayed again protected.
cLoSing the centraL Locking BUtton SerVice
When switched on / off by pressing the service button ignition lock / unlock the
central locking (F20).
aUtomatic reactiVation
If you turn off the car alarm is turned on the ignition or not closed any doors, the
system automatically activates after 30 seconds. F16 function must be turned on. If
F14 is turned on, the reactivation of the central locking locks.
aUtomatic actiVation aFter cLoSing the LaSt door
After switching off the ignition and closing the last door, the car alarm automatically
switches on after 30 seconds. If F14 is turned on, when you turn to lock the central
locking. If within 30 seconds after closing the last door, open door, car alarm is
activated 30 seconds after closing.
cLoSing the centraL Locking to aUtomatic actiVation
If the function is activated F13 and F14 function, the automatic activation after closing
the last door automatically locks and central locking.
memory car aLarm
Car alarm even after disconnecting the power supply maintains the state it was in
before disconnecting
immoBiLizer
After turning the car alarm is activated immobilization output (-300mA) to turn off the
car alarm. Function F10 must be set to ”immobilizer“.
aUtomatic actiVation oF aLarm
After an alarm siren sounds for 30 seconds. After the end of the system remains
activated. If the input that caused the alarm disturbed even after 30 seconds, the system
automatically skips if not in peace again.
directionaL LightS and Siren aLarm
When a car alarm when switched to an alarm, the siren sounds and indicator lights
flash 30 seconds. The alarm caused by contact of the door, bonnet, boot and shock
sensor can be made 8x. After switching off the car alarm and alarm can be triggered
again 8. The alarm caused by turning on the ignition is caused by a limited number of
alarms. The siren sounds until the ignition is switched on..
ii. SerVice mode
1. Turn the ignition on and push the service button 2 times within 8 seconds.
2. Turn the ignition off. If the security mode is not active, siren will sound 2 times and LED
diode will glow permanently. Valet mode is now active. If security mode is active (function
F15), LED will start to flash slowly. Enter the security mode. If you’ve entered correct PIN
code, siren will sound 2 times and LED will glow permanently. Valet mode is now active
deactivate the service mode
Turn on the ignition and press the service button 2 to 8 seconds. Turn off the ignition.
The siren sounds and the LED 2 stops lighting. The service mode is deactivated.
iii. enter SecUrity regime
To enter the secure mode by entering the four-digit PIN code. If the security mode is
activated (feature F15), the programming LED will flash slowly.
When the LED blinks repeatedly, what is the value of the first digit, press the button once
the service. LED starts to flash again.
When the LED blinks repeatedly, what is the value of the second digit, press the button
once the service. LED starts to flash again.
When the LED blinks repeatedly, what is the value of the third digit, press the button
once the service. LED starts to flash again.
When the LED blinks repeatedly, what is the value of the fourth digit, press the button
once the service. LED starts to flash again.
iV. programming SyStem FUnctionS
programming table
When programming the functions, proceed as follows:
1. activate the service mode and turn the ignition .
2. press the service button 7 times to 10 seconds.
3. Turn off the ignition, the LED flashes.
4. press the service button as many times as a function of what number you want set to 20
seconds. After each pressing the service button 1x siren sounds. If the function number
greater than 10, press the service button for 3 seconds. Eg. To set the function number
13, press the service button for 3 seconds. After releasing the button, hear the siren
2. Press the service button 3 times, each time pressing the siren sounds. After turning
the ignition siren sounds with 1 or 2 accordingly to what the state of the function set.
To set the function number 25, press the service button for 3 seconds. After releasing
the siren sounds 2x. Again, press the service button for 3 seconds. After releasing the
siren sounds 2x. Press the service button 5 times. After each pressing the siren sounds.
5. turn on the ignition. Siren sounds with 1 or 2 accordingly to what the state of the
function set.
6. programming quit turning on the ignition and pressing the service button 1x. The
system is in service mode.
V.change pin code
1. Turn the ignition on.
2. Push the valet button 10 times within 10 seconds.
3. Turn the ignition off. If the security mode is turned off, siren will sound 1 time and
will be in PIN programming mode. If the valet mode is active (function F16), LED
will start to flash slowly.
Enter the security mode. If you entered the correct PIN code, siren will sound one
time and LED will stop glowing. You are now in PIN programming mode.
4. Push the valet button. LED will start to flash slowly and you can enter new PIN
code.
- when the LED flashes so many times, which is the new value of first PIN code
number, push the valet button one time. First code number is saved and LED will
start to flash again.
- repeat this step for the second, third and fourth PIN code number.
- 5 seconds after entering the fourth code number LED diode will show the new
PIN code with the number of flashes with 2 seconds pause between every code
number.
5. Turn the ignition on or wait for 10 seconds after showing the new PIN code and
system will automatically end the PIN code programming mode.
reSet pin code
Disconnect the system from power supply. Disjoint the jumper in control unit and
connect the system to the power supply. Within 3 seconds connect the jumper to the
control unit. PIN code will be set to factory default number 4321
.
Vi. remote controLL Learning
1. Turn the ignition on and push the valet button 5 times within 8 seconds. Turn the
ignition off. If security mode is inactive, siren will sound 5 times and the system
will switch to programming mode. LED will start to flash rapidly. If security mode is
active, LED will flash slowly. Enter the security mode. If you entered the correct PIN
code, siren will sound 5 times and you have successfully entered the programming
mode. LED will start to flash rapidly.
2. Push any button on the remote control within 5 seconds. If you don’t push any button
or if you turn off the ignition, system will automatically finish the programming.
3. Siren will confirm programming the remote with a short sound. Depending on
which remote was programmed, so many times will the siren sound. Programming
the first remote will be confirmed with one beep, second remote with two beeps
and third remote with three beeps.
4. If you want to program new remote, you have to program also any other remotes,
which are already programmed in system.
5. System allows to program a maximum of 3 remotes. When programming new
remotes, older ones will be automatically erased from system.
.
Vii. emergency reactiVation
1. Open the doors and turn the ignition on.
2. Push the valet button so many times, which is the value of the first number in PIN
code within 8 seconds and then turn of the ignition. If the security mode is turned
of, siren will sound 2 times, direction lights will flash 2 times and system will be
disarmed. If the security mode is armed (function F18), LED will start to flash
slowly. Enter the security mode. If you have entered correct PIN code, siren will
sound 2 times and direction lights will flash 2 times. System will be disarmed
note
: The equipment includes the TS 10 is a remote control operating in the
433.92 MHz. Declaration of Conformity for the product and request a remote
control with your dealer.
BUtton
FUnction
conditionS
1
a: activation system and lock the central locking
b: vehicle sound search
c: end alarm
d: lock the central locking
deactivated system
activated system
caused alarm
ignition is switched on
2x
1
to 3sec.
omission of additional sensors
Off the ignition, system is deac-
tivated
2
a: deactivation system
b: unlock the central locking
c: end alarm
system activated
ignition is switched on
caused alarm
3
to 1sec.
opening the trunk
ignition is switched on
1+2
emergency panic alarm
always
Prog.
menu
Function
Factory setting
1 tone siren
Adjustable
2 tones siren
F1
quiet / loud activation
silent
loud
F2
central locking system locks the ignition
turned off
turned on
F3
delay activation of inputs
8 sec.
40 sec.
F4
reminders of the system
off
on
F5
input polarity door contacts
“-” inp
u
t
“+” input
F6
double-lock pulse
off
on
F7
double unlock pulse
off
on
F8
polarity of the output sequence
“-” output
“+” output
F9
directional light output
normal
sequential
F10
programmable output
trunk open
im
P
obilizer
F11
unlock time
0,5 se
c
.
3,5 se
c
.
F12
lock time
a
VXQORFNLQJ
20 se
c
.
F13
automatically activated when you close the last door
off
on
F14
lock the central locking system for automatic activation
off
on
F15
security regime
off
on
F16
automatic reactivation
on
off
F17
siren output
siren “+”
horn “-”
F18
type sirens
norm
D
l
coded
F19
visual indication on / off car alarm
on
off
F20
lock / unlock button when servicing the ignition
on
off
F25
system reset
reset
1.
2.
3.
rc 380
