background image

OIL FIRED WATER HEATER

Installation and Operating Manual

KEEP THIS MANUAL IN THE POCKET ON HEATER FOR FUTURE REFERENCE

WHENEVER MAINTENANCE ADJUSTMENT OR SERVICE IS REQUIRED.

ALL TECHNICAL AND WARRANTY QUESTIONS:

 SHOULD BE DIRECTED TO THE LOCAL DEALER FROM WHOM THE WATER HEATER WAS PURCHASED. 

IF YOU ARE UNSUCCESSFUL, PLEASE CONTACT THE COMPANY LISTED ON THE RATING PLATE ON THE WATER HEATER.

1505  

331551-002  

Read and understand instruction 
manual and safety messages 
before installing, operating or 
servicing this water heater.
Failure to follow instructions and 
safety messages could result in 
death or serious injury.
Instruction manual must remain 
with water heater.

WARNING

  

- Improper installation, adjustment, altera-

tion, service, or maintenance can cause 
injury or property damage. Refer to this 
manual. For assistance or additional 
information, consult a qualified Oil-
Burner Technician or your oil supplier.

- Do not store or use gasoline or other 

flammable vapors and liquids in the 
vicinity of this or any other appliance.

- Installation and service must be 

performed by a qualified Oil-Burner 
Technician or your oil supplier.

- WHAT TO DO IF YOU SMELL OIL:

  • Immediately call your oil supplier. 

Follow the oil supplier's instructions.

WARNING: If the information in these 
instructions is not followed exactly, a fire 
or explosion may result causing property 
damage, personal injury or death.

Summary of Contents for JW F657





























Reviews: