1C750W2 (1.5kW) User Manual
General
Your Eco Heat heater has been designed using the
latest in technology. With normal care and
maintenance, your heater will provide years of
satisfactory performance.
This heater has been designed for use on 230 V
circuits. Do not use it in areas where a standard
voltage of 230 V is not provided.
If, after reviewing this guide, you require additional
information or assistance please contact Eco Heat
Equipment at
[email protected], +27 (0)861 999
887, or www.ecoheat.co.za.
Technical Specifications
Power consumption: 1500W
Dimensions: 124.7cm(L) x 5.3cm*(W) x
13.6cm(H) (* excludes mounting bracket)
Indoor heat coverage area:
±
15 m
²
to 20 m
2
Power density:
±
75W per m
²
to 100W per m
2
Weight:
±
3.5 kg
Minimum cord length: 2 m
Electrical Classification: class I device
Input: 230 V, 50 Hz
Safety
Any use not recommended by the manufacturer
may cause fire, electrical shock or injury to persons.
This heater is hot when in use, to avoid burns,
do not let bare skin touch it.
Keep combustible materials such as furniture,
pillows, bedding, clothes and curtains at least
1 m away from the heater.
Do not cover or hang anything over the heater
as it may combust.
Fire risk exists if heater is covered or positioned
incorrectly.
Never leave the heater unattended while in
use.
Always turn the heater off when it is not in use.
Avoid using an extension cord as this may
overheat and cause a risk of a fire. If an
extension cord must be used, make sure it is
rated for 10 A.
To move the heater, switch heater off and let it
cool for at least 15 minutes.
Never locate the heater where it might fall into
a bathtub or other water container.
If the heater is to be used in a bathroom, the
heater is to be installed so that switches and
other controls cannot be touched by a person
in the bath or shower.
Do not insert foreign objects past the heaters
grid. The elements are extremely hot and the
risk of electrical shock under fault conditions
exists.
Do not use the heater in rooms with explosive
gas (e.g. petrol) or while using flammable
substances.
Keep the mains cord at a safe distance from
the main body of the heater.
Do not run the cord of the heater under
carpeting. Do not cover the cord with throw
rugs, runners or other floor coverings. Arrange
the cord away from traffic areas where it will
not be tripped over.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order to
avoid a hazard.
Mounting/Installation
Your box should contain the following items:
One 1C750W2 heater
Two bolts
Four ring washers
Two wall mounting brackets
Two spring washers
Two nuts
Step 1 – Bracket assembly
Assemble the bracket in the following order:
a.
Bolt, ring washer, heater bracket, wall mounting
bracket, ring washer, spring washer, nut.
Step 2 – Heater positioning
a.
Install the heater 1.8 m to 2.3 m above the floor.
b.
A minimum unobstructed distance (minimum
clearance) of 200 mm must be maintained
between the heater and any object that may
affect the operation or safety of the heater.
c.
Mount/place the heater where it is out of reach
of small children.
Step 3 – Wall Mounting
a.
The wall mounting structure and the anchoring
provisions must be of sufficient strength to
support the weight of the heater, elements and
all accessories.
b.
Ensure the heater is mounted with the ‘This side
up’ sticker pointing up.
c.
Attach the heater to the wall with four
screws/bolts using the holes provided in the wall
mounting bracket.
Electrical Installation
All wiring must be done in accordance with
National and Local Electrical Codes and
Standards.
The heater operates from a normal 15 A 3 pin
socket outlet on earth leakage on a 230 V system,
or connects directly on a 230 V, 2-pole isolator on
earth leakage.
Operation
The heater will automatically start working once it
has been connected to the correct 230 V power
source. The LED light will glow to indicate the
heater is on.
Radiant heat will be felt in front of the reflector
after about 30 seconds, and continue to increase
in intensity for 3-4 minutes.
Infrared Radiation
The heater uses infrared radiation to heat objects.
Do not stare into the heater for prolonged periods
at a short distance without adequate eye
protection as this may cause damage to the eyes.
Take adequate precautions to safeguard against
excessive exposure, such as moving further away
from the heater or switching the heater off when
heat becomes uncomfortable.
Maintenance
The heater contains no user serviceable parts.
The elements should last in excess of 10 000 hours.
If the heater has not been in use for a while, ensure
it is disconnected from the power source. Dust the
elements with a soft duster to remove excess dust.
This should prevent odors after first use.
Cleaning
Clean the outside of the heater only when it is
disconnected from the power source and cool. If it
has been in operation, switch off and wait for at
least 15 minutes.
Carefully wipe the exterior of the heater with a soft
damp cloth and dry thoroughly with a dry cloth. Do
not use harsh or abrasive cleaners to clean your
heater, as these may damage the surface.
Do not let the inside of the heater get wet as this
may cause a risk of electrical shock.
Recycling
Please recycle all packaging material that came
with the heater.
If you are replacing an old heater, please go to
www.ewasa.org or contact Eco Heat for
information on responsible disposal or recycling.
Warranty
The heater has a one year warranty after the date
of the original purchase. Please keep your original
receipt, as this will be required for any claims under
this warranty.
The warranty covers workmanship, materials and is
limited to the purchase price of the heater.
The warranty does not cover:
damage from misuse,
neglect or abuse,
products that have been modified in any way,
shipping and handling cost associated with the
replacement of the product.
For more information, view the Returns / Refund
Policy at www.ecoheat.co.za/terms.php.
Trouble shooting
If the heater is plugged into a live 230 V power
source and no heat is felt after 3-4 minutes the
heater may be faulty.
Try ONE of the following:
a.
Ensure the power source is working.
b.
Unplug the heater and have a certified
electrician test the electrical circuitry. If the
circuitry is in working order, the elements might
need replacement.
Contact Eco Heat Equipment for a
replacement element.
Replacement parts
Replacement elements can be ordered at
www.ecoheat.co.za.
Due to minor improvements in design or otherwise, the
product you buy may differ from the one shown in this
leaflet. For more information or advice on this or any
other Eco Heat Equipment products, visit
www.ecoheat.co.za or phone +27 (0)861 999 887.
!
