Johnson Gas Appliance FV34-PF2 Installation Instructions Manual Download | Manualshive

Page: 1 / 76

background image

85-03-00954

1 |

P a g e

FULLVIEW RECTANGLE DIRECT VENT GAS FIREPLACE HEATER

Model FV34-PF2

INSTALLATION INSTRUCTIONS MANUAL

DOCUMENT NO. FV34-PF2-IM-1015

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

INSTALLATEUR

: Laissez cette notice avec l’appareil.

CONSOMMATEUR

: Conservez cette notice pour consulta-

tion ultérieure.

WARNING: If the information in this manual is not followed
exactly, a fire or explosion may result causing property dam-
age, personal injury or loss of life.

Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.

WHAT TO DO IF YOU SMELL GAS



Open windows.



Do not touch electrical switches.



Do not try to light any appliance.



Extinguish any open flame.



Do not use the phone in your building.



Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier’s instructions.



If you cannot reach your gas supplier, call the fire
department.



Installation and service must be performed by a
qualified installer, service agency or the gas suppli-
er.

WARNING

Do NOT use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control, which has been under water.

AVERTISSEMENT: Assurez-vous de bien suivre les instruc-
tions donné dans cette notice pour réduire au minimum le
risque d’incendie ou pour éviter tout dommage matéeriel,
toute blessure ou la mort.



Ne pas entreposer ni utiliser d'essence ni d'autres vape-
rurs ou liquides inflammables dans le voisinage de cet
appareil ou de tout autre appareil.



QUE FAIRE SI VOUS SENTEZ UNE ODEUR
DE GAZ:



Ne pas tenter d'allumer d'appareil.



Ne touchez à aucun interrupteur. Ne pas vous servir
des téléphones se trouvant dans le batiment où vous
vous trouvez.



Appelez immédiatement votre fournisseur de gaz depuis
un voisin. Suivez les instructions du fournisseur.



Si vous ne pouvez rejoindre le fournisseur de gaz, appe-
lez le service dos incendies.



L'installation et service doit être exécuté par un quali-
fié installer, agence de service ou le fournisseur de gaz.

1
2
3
...
»

Summary of Contents for FV34-PF2













































































Reviews:

No comments

Related manuals for FV34-PF2

Brand: IHP Pages: 12

Brand: Rinnai Pages: 24

Brand: Continental Fireplaces Pages: 52

Brand: Hearth & Home Pages: 2

Brand: Calflame Pages: 32

Brand: Jeco Pages: 4

Brand: Napoleon Pages: 2

Brookhaven 20DVT

Brand: Vermont Castings Pages: 32

Brand: Boulevard Pages: 64

Brand: Heatmaster Pages: 26

Brand: Amantii Pages: 36

Brand: Jøtul Pages: 12

FireBrick Gas Insert ADI-ZCFB-S

Brand: Heatilator Pages: 2

Brand: Lennox Pages: 4

Brand: Coleman Pages: 2

Brand: Hearth and Home Technologies Pages: 4

Brand: Vermont Castings Pages: 68

Brand: Blumfeldt Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands