WRZ-SST-100 Wireless Sensing System Tool
1
Applications
The WRZ-SST-100 Wireless Sensing System Tool is a
lightweight, portable, wireless receiver designed to
receive wireless data transmissions from WRZ-TTx
Series Sensors in one-to-one sensing system site
survey applications. It also serves as a signal test
receiver or site survey tool prior to installing a ZFR1800
Series Wireless Field Bus System.
Use the WRZ-SST-100 Sensing System Tool prior to
installation to verify the optimum locations for
WRZ-TTx Series Sensors and WRZ-7840-0 Receivers
in wireless room temperature sensing system
applications; or for ZFR1810 Coordinators, ZFR1811
Routers, and WRZ-TTx Series Sensor in wireless field
bus applications.
North American Emissions Compliance
United States
Canada
Installation
Transport the WRZ-SST-100 Wireless Sensing System
Tool in the original container to minimize vibration and
shock damage to the receiver.
Verify that all the parts shipped with the receiver:
•
one WRZ-7840 Receiver with two magnets
attached
•
one battery pack with two magnets attached
•
two alkaline batteries
•
one installation instruction sheet
This equipment has been tested and found to comply with
the limits for a Class A digital device pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
this equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be
required to correct the interference at his/her own
expense.
RF Transmitters: Compliance Statement (Part 15.19)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Warning (Part 15.21)
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This Class (A) digital apparatus meets all the
requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la Classe (A) respecte toutes
les exigences du Règlement sur le matériel brouilleur du
Canada.
RF Transmitters: Industry Canada Statement
The term
IC
before the certification/registration number
only signifies that the Industry Canada technical
specifications were met.
Le terme « IC » précédant le numéro d'accréditation/
inscription signifie simplement que le produit est conforme
aux spécifications techniques d'Industry Canada.
Section 5.5 of RSS-210
This device has been designed to operate with an antenna
having a maximum gain of 2 dB. Antenna having a higher
gain is strictly prohibited per regulations of Industry
Canada. The required antenna impedance is 50 ohms.
Cet appareil a été conçu pour fonctionner avec une
antenne d'un gain maximum de 2 dBi. En application des
réglementations d'Industry Canada, l'utilisation d'une
antenne de gain supérieur est strictement interdite.
L'impédance d'antenne requise est de 50 ohms.
Section 5.11 of RSS-210
To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (EIRP) is not more
than that required for successful communication.
Pour réduire les interférences radio potentielles avec les
dispositifs d'autres utilisateurs, le type d'antenne et son
gain doivent être choisis de façon à ce que la puissance
isotrope rayonnée équivalente (PIRE) ne soit pas
supérieure à la puissance nécessaire pour une bonne
communication.
WRZ-SST-100 Wireless Sensing System Tool
Installation Instructions
Part No. 24-10393-17, Rev. A
Issued February 26, 2009
Supersedes June 25, 2008
