Johnson Controls MP-802 P9M0 Скачать руководство пользователя

Страница: 1 / 22

D-308439 MP-802 PG+ Rev.0

MP-802 PG+ Wireless PIR Motion Detector

Installation Guide

Installation guidelines

The reference to MP-802 PG+ throughout this manual includes the model MP-802 P9M0.

CAUTION:

Only qualified personnel may install this equipment. Place this device in non-

hazardous indoor locations only.

Important:

Check the device and the entire alarm system weekly to ensure optimal

performance.

Note:

To comply with FCC and ISED Canada RF exposure compliance requirements, locate

the device at a distance of at least 20 cm from all persons during normal operation. Do not
co-locate the antennas used for this product, or operate them in conjunction with any other
antenna or transmitter.

Figure 1: MP-802 PG+

Callout

Description

Lens

Battery pull-tab

Enroll button

Tamper switch

For more information refer to

About MP-802 PG+

*D-308439*

D-308439

Содержание MP-802 P9M0























Результаты поиска

Содержание MP-802 P9M0

Отзывы:

Похожие инструкции для MP-802 P9M0

Бренды по названию

Популярные бренды

Johnson Controls MP-802 P9M0, Руководство по установке

Результаты поиска

Содержание MP-802 P9M0

Отзывы:

Похожие инструкции для MP-802 P9M0

Бренды по названию

Популярные бренды