background image

         

Jersey Instruments 

Patriot

 

 

FACETING MACHINE 

 

 

 

Features.

     

                   Variable Speed Motor, Forward and Reverse            Swinging Post. (No clamping or unclamping) 
                   Rack and Pinion to Raise and Lower Head                .1 Degree Digital Angle Readout 

 
 Includes. 
                

96, 80, 72 Tooth Index Wheels 

                   12 Brass Dops , 3mm. to 8mm. in Flat Cone and V Form 
                   45

Angle Dop. Two Setting Dops.                    

                   Transfer Block. 
 

 Available From. 
                            Jersey Instruments  

                           Phone: 256-883-8988 

                                   805 Halstead Ct.                                        

Email: 

[email protected]

                       

                                   Huntsville, AL USA 35803                        

Web:  www.JerseyInstruments.com

                         

                                       

                              

Designed and manufactured by Jersey Instruments, 805 Halstead Ct. Huntsville, Al.  35803 USA. 

 

Summary of Contents for Patriot















Reviews: