background image

08.10.09 10:23

Seite 1 von 8

Installation Instructions Product-Ident: 45180

doorboards include speakers, Audi A3 8P Sportback

Technical Details:

Car Features:

4-doors, electrical window controls

Model/Year:

8PA (09.2004)

Setup-Advice:

To reach the best performance, the setup of the

radio (Bass, Loudness etc.) should be null or

neutral.

recommended amplifier power:

from 2x 100 - 200 Watt / 2 Ohm

Parts list:

1x

Doorboards (right+left) Audi A3 8P Sportback, covered

1x

grills (right+left) Audi a3 8p sportback , cover: acoustic fabric

2x

XE 26 - Neodymium-Tweeter ø 26mm (1

")  incl. mounting device, Hex nut M4, washer ø 12mm

2x

XM 110 - High-End-midrange driver, ø 100mm (4"),  incl. adapter ring

4x

XM 165 - Low midrange driver, power woofer ø 165mm (6,5

")

1x

3-way frequency crossover (right+left) Audi A3 -sportback - part-no. 45180

1x

Hardware bag, Audi A3 -sportback - part-no. 45180/41180

2x

 flat head srew M4 x 40

2x

 flat head srew M4 x 50

2x

 flat head srew M4 x 60

16x

 hex nut M4

6x

spax screw 4,5 x 80

4x

 Velcro strip à 2,5 cm (reserve)

12x

 washer 12mm

12x

 washer 20mm

Garantee:

We grant a manufacturers guarantee of 2 years starting from the date of purchase of the doorboard or sound system from the dealer. Within this
guarantee period to our choice we either repair or replace free of charge all defects due to material or workmanship. Exempt from this guarantee
are damages due to improper use, wear and tear or damages which have to be led back on wear or interventions by third parties. The guarantee
does not cover subsequent damages or such defects that only insignificantly impair the value or the usability of the doorboard/sound system. The
guarantee does not cover damages due to external influences. Doorboards with additional or wrong assembly drill holes cannot be returned. These
are damages to the doorboard which cannot be repaired again.

Summary of Contents for 45180











Reviews: