IronStrike 32FS Installation And Operation Manual Download

Page: 1 / 38

INSTALLATION AND OPERATION MANUAL

Save These Instructions

For Future Reference

Free-Standing

Pellet Stove

P/N 900116-00, Rev. A, 05/2015

Pellet Stove

Model Montage™ 32FS

WARNING

•

Hot! Do not touch! The glass and surfaces of this appliance will be

hot during operation and will retain heat for a while after shutting off

the appliance. Severe burns may result.

•

Carefully supervise children in the same room as appliance.

•

IHP pellet-burning appliances are designed for use as a supplemental

heater. They are not intended for continuous use as a primary heat

source.

A French manual is available upon request. Order P/N 900117-00.

Ce manuel d’installation est disponible en francais, simplement en faire la demande. Numéro de la pièce

900117-00.

This appliance must be properly installed and operated in order to prevent the possibil-

ity of a house fire. Please read this entire manual before installation and use of this

pellet fuel-burning room heater. Failure to follow these instructions could result

in property damage, bodily injury or even death. Contact your local building

or fire officials to obtain a permit and information on any installation

requirements and inspection requirements in your area.

P900116-00

Report No. 14-200

Summary of Contents for 32FS







































Search results

Summary of Contents for 32FS

Reviews:

Related manuals for 32FS

Brands by name

Popular brands

IronStrike 32FS, Installation And Operation Manual

Search results

Summary of Contents for 32FS

Reviews:

Related manuals for 32FS

Brands by name

Popular brands