background image

Printed in U.S.A.

           

440 04 6001 00 

  3/31/2014

SERVICE AND TECHNICAL

SUPPORT MANUAL

Single Stage, PSC Blower Motor

35” Tall, High Efficiency Condensing Gas Furnace

R9MSB (B Series)

Save this manual for future reference.

Safety Labeling and Signal Words

DANGER, WARNING, CAUTION, and NOTE

The signal words 

DANGER, WARNING

,

CAUTION

,

 

and

 NOTE 

are used to identify levels of

hazard seriousness. The signal word

 DANGER 

is

only used on product labels to signify an immediate

hazard. The signal words 

WARNING

CAUTION

,

and 

NOTE

 will be used on product labels and

throughout this manual and other manual that may

apply to the product.

DANGER

 

 Immediate hazards which will result in

severe personal injury or death.

WARNING

 

 Hazards or unsafe practices which

could result in severe personal injury or death.

CAUTION 

 Hazards or unsafe practices which

may result in minor personal injury or product or

property damage.

NOTE 

 Used to highlight suggestions which will

result in enhanced installation, reliability, or

operation.

!

WARNING

Signal Words in Manuals

The signal word 

CAUTION

 is used throughout

this manual in the following manner:

!

CAUTION

Signal Words on Product Labeling

Signal words are used in combination with

colors and/or pictures or product labels.

The signal word 

WARNING

 is used throughout

this manual in the following manner:

Safety

alert symbol

When you see this symbol on the unit and in

instructions or manuals, be alert to the

potential for personal injury.

TABLE OF CONTENTS

START

UP, ADJUSTMENT, AND SAFETY CHECK

3

. . . .

GENERAL

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PRIME CONDENSATE TRAP WITH WATER

3

. . . . . . . . . .

PURGE GAS LINES

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ADJUSTMENTS

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CHECK INLET GAS PRESSURE

4

. . . . . . . . . . . . . . . . . . . .

ADJUST MANIFOLD PRESSURE

5

. . . . . . . . . . . . . . . . . . .

ADJUST TEMPERATURE RISE

6

. . . . . . . . . . . . . . . . . . . . .

ADJUST BLOWER OFF DELAY (HEAT MODE)

7

. . . . . . .

BLOWER OFF DELAY JUMPER POSITIONS

7

. . . . . . . . .

ADJUST COOLING AIRFLOW

7

. . . . . . . . . . . . . . . . . . . . . .

ADJUST THERMOSTAT HEAT ANTICIPATOR

7

. . . . . . . .

CHECK SAFETY CONTROLS

7

. . . . . . . . . . . . . . . . . . . . . .

CHECKLIST

7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ALTITUDE DERATE MULTIPLIER FOR U.S.A.

8

. . . . . . . .

GAS RATE (CU FT./HR)

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

ORIFICE SIZE AND MANIFOLD PRESSURE

11

. . . . . . . . .

ORIFICE SIZE AND MANIFOLD PRESSURE

12

. . . . . . . . .

SERVICE AND MAINTENANCE PROCEDURES

13

. . . . . .

PRESSURE SWITCHES

13

. . . . . . . . . . . . . . . . . . . . . . . . . . .

CLEANING HEAT EXCHANGERS

19

. . . . . . . . . . . . . . . . . . .

SEQUENCE OF OPERATION

23

. . . . . . . . . . . . . . . . . . . . . .

PARTS REPLACEMENT INFORMATION GUIDE

27

. . . . . .

MODELS

R9MSB0601716B

R9MSB0801716B

R9MSB1002120B

R9MSB1202420B

Use of the AHRI Certified TM Mark indicates a

manufacturer’s participation in the program.

For verification of certification for individual

products, go to www.ahridirectory.org .

Summary of Contents for R9MSB0601716B




























Reviews: