F-17-V & 17-V
EXIT DEVICES
INSTALLATION INSTRUCTIONS
1) MAKE SURE THE CORRECT DEVICE IS BEING USED, AND IS THE CORRECT HANDING (SEE PAGE #16 FOR REVERSING
INSTRUCTIONS).
2) MAKE SURE ALL NEEDED PARTS ARE ON HAND.
NOTE: LIST DOES NOT REFLECT ALL POSSIBLE APPLICATIONS.
3) MAKE SURE OUTSIDE TRIM (IF BEING USED) HAS BEEN PROVIDED AND IS THE CORRECT HANDING.
1
PARTS CHECK
6) VERTICAL RODS (LENGTHS FOR 7'0" OPENINGS)
TOP ROD= 36"
BOTTOM ROD = 37-1/4" (WITH DEAD BOLT)
5) SCREW PACK FOR FIRE DEVICE
MOUNTING BRACKET
(1 QTY.)
SEX BOLT – 1/4"-20 THREAD
(1 QTY.)
1/4" - 20 x 3/4" TPHMS (1 QTY.)
#10-24x3/4" FPHMS (6 QTY.)
#10-24x3/4" PPHMS (4 QTY.)
1/4"-20x3/4" PPHMS (2 QTY.)
1/8" x 1" COTTER KEY (1 QTY)
ROD GUIDE (2 QTY.)
ROD GUIDE INSERT (2 QTY)
ROD GUIDE BRACKET (2 QTY)
CHANNEL END CAP (1 QTY)
#10-24x3/8" PPHMS w/NYLON
PATCH (2 FINISHED)
#8-32x1/4" UFPHMS (4 FINISHED)
4) SCREW PACK FOR PANIC DEVICE
DOGGING KEY (1 QTY.)
MOUNTING BRACKET
(1 QTY.)
SEX BOLT – 1/4"-20 THREAD
(1 QTY.)
1/4" - 20 x 3/4" TPHMS (1 QTY.)
#10 x 1-1/4" FPHSMS
(6 QTY. (2 FINISHED))
#10 x 1-1/4" PPHSMS (4 QTY.)
#14x1" PPHSMS (2 QTY.)
1/8" x 1" COTTER KEY (1 QTY)
ROD GUIDE (2 QTY.)
ROD GUIDE INSERT (2 QTY)
ROD GUIDE BRACKET (2 QTY)
CHANNEL END CAP (1 QTY)
#10-24x3/8" PPHMS w/NYLON
PATCH (2 FINISHED)
#8-32x1/4" UFPHMS (4 FINISHED)
1) (F) 17-V DEVICE
NOTE: DEVICE IS FIELD REVERSIBLE
2) STRIKE
4163/3788
2130
2126A
4155
(F)17-V
FIRE
TOP
3788
BOTTOM
2130
PANIC
TOP
4163
BOTTOM
2130
OPT. BOTTOM
4155
OPT. BOTTOM
2126A
3) LATCHES & BOTTOM BOLTS
TOP LATCH
BOTTOM
LATCH
D-1128-a Copyright © 2008 Ingersoll-Rand Company Limited
PAGE 16
5
REVERSING INSTRUCTIONS
TO REVERSE THE HANDING OF AN (F)17-V DEVICE
1) REMOVE CHASSIS COVER AND FOUR SCREWS (NOT SHOWN).
2) REMOVE COVER PLATE
A
(4 SCREWS NOT SHOWN).
3) REMOVE MAIN CAM
B
AND TRIM CAM
C
. NOTE: DO NOT REMOVE SLIDEBAR
D
.
4) PLACE MAIN CAM
B
AND TRIM CAM
C
IN CORRECT LOCATION FOR APPOPRIATE HANDING AS SHOWN IN
FIGURE 1 OR 2.
5) REMOVE SPACER
E
(1 SCREW, NOT SHOWN) AND PLACE IN OPPOSITE END OF SLIDEBAR
D
PER FIGURE 1 OR 2.
6) REASSEMBLE COVER PLATE
A
(4 SCREWS NOT SHOWN).
7) PROCEED WITH INSTALLATION.
FIGURE 2
(LHR)
FIGURE 1
(RHR)
FRONT VIEW OF DEVICE
D-1128
