Indian Motorcycle 2880986 Скачать руководство пользователя | Manualshive

Страница: 1 / 9

background image

P/N 9925955 Rev 02 04/15 Page 1 of 9

BEFORE YOU BEGIN

Read these instructions and check to be sure all parts and tools are accounted for. Please retain
these installation instructions for future reference and parts ordering information.

P/N 2880986

SADDLEBAG AUDIO WIRE

HARNESS KIT

APPLICATION

ALL INDIAN MOTORCYCLES WITH BOTH TRUNK AND SADDLEBAG AUDIO INSTALLED

KIT CONTENTS

Ref

Qty

Part Description

Part Number

1

1

Vehicle Harness

2412576

2

1

Harness, Audio, Accy

2412815

3

4

Panduit

7080138

1

Instructions

9925955

APPROXIMATE ASSEMBLY TIME

90 min

TOOLS NEEDED

Socket

Extension

Flashlight

Ratchet

Diagonal

Cutters

10

mm

Socket

Set

Cutters

10 mm Open End Wrench

4 mm Hex Key Socket (Standard)

Torque Wrench

5 mm and 6 mm Hex Key Sockets

4 mm Hex Key Socket (Ball-End Long)

2

1

3

IMPORTANT

Your Indian SADDLEBAG AUDIO WIRE HARNESS KIT is exclusively designed for your vehicle.

Please read the installation instructions thoroughly before beginning. Installation is easier if
the vehicle is clean and free of debris. For your safety, and to ensure a satisfactory installation,
perform all installation steps correctly in the sequence shown.

1
2
3
...
»

Содержание 2880986










Отзывы:

Нет отзывов

Похожие инструкции для 2880986

Бренд: Nederman Страницы: 2

Бренд: StarTech.com Страницы: 4

Бренд: W Box Technologies Страницы: 26

Бренд: Oasis Страницы: 3

Бренд: Speaka Professional Страницы: 4

Бренд: Speaka Professional Страницы: 4

Бренд: Speaka Professional Страницы: 8

Бренд: NEUTRIK Страницы: 13

Raychem FrostGuard

Бренд: Pentair Страницы: 8

Raychem FrostGuard 240 V

Бренд: Pentair Страницы: 4

Бренд: Blonder tongue Страницы: 8

Бренд: Optics Страницы: 5

Бренд: KanexPro Страницы: 7

USB 2.0 Link Cable

Бренд: Hama Страницы: 20

Бренд: Tapkey Страницы: 5

Бренд: Bals Страницы: 28

Бренд: Masimo Страницы: 95

Frostvakt 25 Series

Бренд: EBECO Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды