background image

 

WAFER-5822 

Low Power GXLV/GX1 MMX   

with SVGA/LCD/TV, 

Ethernet, & Audio SBC. 

 
 
 

Copyright Notice 

©2000 Copyright by ICP Electronics Inc. All rights reserved. Manual first 

edition Aug.15, 2000. 

The information in this document is subject to change without prior notice in 

order to improve reliability, design and function and does not represent a 

commitment on the part of the manufacturer. 

In no event will the manufacturer be liable for direct, indirect, special, 

incidental, or consequential damages arising out of the use or inability to use 

the product or documentation, even if advised of the possibility of such 

damages. 

This document contains proprietary information protected by copyright. All 

rights are reserved. No part of this manual may be reproduced by any 

mechanical, electronic, or other means in any form without prior written 

permission of the manufacturer.  

Trademarks

 

WAFER-5822 is a registered trademark of ICP Electronics Inc. IBM PC is a 

registered trademark of International Business Machines Corporation. Intel is 

a registered trademark of Intel Corporation.  Other product names mentioned 

herein are used for identification purposes only and may be trademarks and/or 

Summary of Contents for Wafer 5822



















































Reviews: