background image

 

JUKI-511P –PCISA BUS 

Low Power GXLV/GX1 MMX with 

  SVGA/LCD, Ethernet, & Audio SBC. 

 

 
 
 

Copyright Notice 

©Copyright 2001 by ICP Electronics Inc. All Rights Reserved. Manual second edition 
December.26, 2001. 

The information in this document is subject to change without prior notice in order to 
improve reliability, design and function and does not represent a commitment on the 
part of the manufacturer. 

In no event will the manufacturer be liable for direct, indirect, special, incidental, or 
consequential damages arising out of the use or inability to use the product or 
documentation, even if advised of the possibility of such damages. 

This document contains proprietary information protected by copyright. All rights are 
reserved. No part of this manual may be reproduced by any mechanical, electronic, or 
other means in any form without prior written permission of the manufacturer. 

Trademarks

 

JUKI-511P is a registered trademark of ICP Electronics Inc. IBM PC is a registered 
trademark of International Business Machines Corporation. Intel is a registered 
trademark of Intel Corporation.    Other product names mentioned herein are used for 
identification purposes only and may be trademarks and/or registered trademarks of 
their respective companies . If you have any questions or need  other information , 
please connect to our web site.   

http://www.iei.com.tw   

 

 

 1

Contents

 

Introduction .............................................................................. 3 

1.1 Specifications............................................................................ 4 
1.2 What You Have......................................................................... 6 

Installation................................................................................ 7 

2.1 JUKI-511P Board Layout ......................................................... 7 
2.2 Unpacking Precautions ........................................................... 11 
2.3 Watchdog Timer Setting (JP1)................................................ 11 
2.4 LCD Voltage and Clock Setting (JP2) .................................... 12 
2.5 Compact Flash Setting (JP4) .................................................. 12 
2.6 COM2 Setting JP5,JP6(2,4,6)................................................. 12 
2.7 Clear CMOS Setup (JP6/1,3,5)............................................... 13 

Connection............................................................................. 14 

3.1 LCD Interface Connector (CN1) ............................................ 14 
3.2 VGA Connector (CN2) ........................................................... 16 
3.3 External Switches and Indicators (CN3) ................................ 16 
3.4 External Power Connector (CN4)........................................... 17 
3.5 Audio Connector (CN5,CDIN1)............................................. 17 
3.6 ATX Power Connector (CN6,CN7) ........................................ 18 
3.7 LAN RJ45 Connector (CN16)................................................ 19 
3.8 USB Port Connector (CN17).................................................. 19 
3.9 CompactFlash Connector -- TYPE II (CN18) ........................ 20 
3.10 E-IDE Hard Disk    Connector (CN19) ................................ 21 
3.11 Serial Ports (CN20, CN21) ................................................... 22 
3.12 Keyboard & PS/2 Mouse Connector (CN22,CN23) ............ 23 
3.13 IrDA Infrared Interface Port (CN24) .................................... 23 
3.14 Parallel Port (CN25) ............................................................. 24 
3.15 Floppy Disk Drive Connector (CN26) ................................. 25 

Summary of Contents for JUKI-511P


























Reviews: