![background image](http://html.mh-extra.com/html/ic/pressure-governor/pressure-governor_quick-start-manual_609413001.webp)
Pressure Governor Quick Start Guide
Use the appropriate Innovative Controls 4000675 series wiring harnesses for your
application. Install the Fire Pressure Governor wiring harnesses on the rear of the unit
and connect the vehicle power, interlocks, pump pressure sensors, and engine CAN
network or analog control signals to the field wiring side of the cable harnesses.
The illustration below shows the six different standard FPG cable harnesses:
Models 3050621, 3050622, 3050623, and 3050624
1
2
3
4
5
6
7
8
9
10
11
12
ENGINE (+) REF
THROTTLE READY
HIGH IDLE
DISCHARGE SENSOR GND
DISCHARGE SENSOR REF
DISCHARGE SENSOR SIG
ENGINE SIGNAL
ENGINE (-) REF
PUMP ENGAGED
DELAY RELAY COM
DELAY RELAY N.O.
Pin
Name
Red
White
White
Black
Red
White
Yellow
Black
White
Orange
Blue
Wire
THROTTLE READY
PUMP ENGAGED
HIGH IDLE
Name
White
White
White
Wire
Interlocks
ENGINE (+) REF.
ENGINE (-) REF.
ENGINE SIGNAL
DELAY RELAY COM.
DELAY RELAY N.O.
Name
Red
Black
Yellow
Orange
Blue
Wire
Analog Control
CABLE
4000675-03
CABLE
4000675-02
CABLE
4000675-04
Models 3050621 and 3050623
1
2
3
4
5
6
SYSTEM POWER
SYSTEM GROUND
ALARM
SAE CAN HI
SAE CAN LO
SAE CAN SHIELD
Pin
Name
Red
Black
Blue
Yellow
Green
Shield
Wire
SYSTEM POWER
SYSTEM GROUND
ALARM
Name
Red
Black
Blue
Wire
Power and Alarm
SAE CAN HIGH
SAE CAN LO
SAE CAN SHIELD
Name
Yellow
Green
Shield
Wire
SAE J1939 CAN
CABLE
4000675-01
12 Pin Key A
12 Pin Key B
6 Pin
SYSTEM POWER
SYSTEM GROUND
ALARM
Name
Red
Black
Blue
Wire
Power and Alarm
IC CAN HIGH
IC CAN LO
IC CAN SHIELD
Name
Yellow
Green
Shield
Wire
IC J1939 CAN
SENSOR GROUND
5 REF.
SENSOR SIGNAL
Name
Black
Red
White
Wire
Intake Sensor
CABLE
4000675-05
IC CAN HIGH
IC CAN LO
IC CAN SHIELD
Name
Yellow
Green
Shield
Wire
IC J1939 CAN
CABLE
4000675-06
SAE CAN HIGH
SAE CAN LO
SAE CAN SHIELD
Name
Yellow
Green
Shield
Wire
SAE J1939 CAN
Models 3050622, and 3050624
1
2
3
4
5
6
7
8
9
10
11
12
SYSTEM POWER
SAE CAN HI
SAE CAN SHIELD
IC CAN HI
INTAKE SENSOR GND
INTAKE SENSOR REF
INTAKE SENSOR SIG
IC CAN SHIELD
IC CAN LO
ALARM OUT
SAE CAN LO
SYSTEM GROUND
Pin
Name
Red
Yellow
Shield
Yellow
Black
Red
White
Shield
Green
Blue
Green
Black
Wire
SENSOR GROUND
5 REF.
SENSOR SIGNAL
Name
Black
Red
White
Wire
Discharge Sensor
MOUNTING
WIRING
During power up the FPG displays the installed software version, and the current
date and time. After initialization the FPG goes into READY mode by default.
Verify that the Throttle Ready and OK to Pump interlocks operate correctly using the
LED indicators and Status display on the front panel of the FPG.
The Status display will show OK to PUMP when both the Throttle Ready and Pump
Engaged interlock inputs are active. If the engine is communicating correctly with the
FPG the engine speed will be shown in the RPM display, otherwise the Status display
will show NO J1939 ENGINE COMM.
The Engine Temperature, Oil Pressure, and Transmission Temperature, and Battery
icons will all be green if their conditions are normal. A yellow or red icon is an
indicates a problem and additional information will be shown on the Status display.
Press the PRESSURE button to place the FPG in pump pressure control mode.
Press the RPM button to place the FPG in engine speed control mode. Use the
rotary knob, or the + and – buttons to adjust the pump pressure or engine speed
setpoints.
The PRESET button is used to set the pump pressure or engine speed to a pre-pro-
grammed setting. The IDLE button causes the FPG to slow the engine to curb idle
speed and return to READY mode.
(continued on back)
OPERATION
4.00
3.50
0.21
DIA.
TYP.
5.75
0.50
RAD.
TYP.
The panel cutout for the Fire Pressure
Governor (FPG) is shown below in inches.
Use four #10 screws to mount the unit to
the pump panel.
PRESSURE SENSORS
Use Innovative Controls pressure sensor
part numbers 3050471 or 3050472 for
300 or 600 PSI full scale discharge
pressure measurement. Use the 3050473
or 3050474 pressure sensor for 300 or 600
PSI intake pressure measurement. Install the
pump discharge pressure sensor on the
discharge manifold side of the pump.
Install the pump intake pressure sensors on
the intake manifold side of the pump when
applicable.