IAG IAG-ENG-7252 Installation Manual Download

Page: 1 / 36

IAG Performance | 1203 Baltimore Blvd. Westminster, MD 21157 | Ph: 410-840-3555 | www.iagperformance.com

IAG Competition Series Air / Oil Separator (AOS) For 2015-16 WRX

Part# IAG-ENG-7252

Tools Required:

Ratchet, torque wrench, extensions,

needle nose pliers, hose cutter, snips/scissors, flat head

screw driver, hose clamping pliers, pop clip pliers

Sockets: 10mm, 12mm, 13mm, 19mm,

Wrenches: ⅞”, 8mm, 10mm, 13mm, 3mm & 5mm allen,

Other: Electrical Tape

Congratulations on the purchase of your Air/Oil Separator

(AOS) and thank you for choosing IAG Performance. This

installation manual is intended to guide you through the

removal of the factory PCV system and the installation of

the IAG AOS. If you already have an aftermarket catch can

or AOS installed, please consult the specific instructions for

your hardware to aid in its removal.

Parts List

Part Name

Quantity

Notes

Air/Oil Separator

Top Coolant Hose Assembly

43” Hose Length, ½” I.D., -8ORB

Bottom Coolant Hose Assembly

15” Hose Length, ½” I.D., -8ORB, ½” Straight Plastic Barb

AOS Vent Hose

55” Hose Length, 1” ID

Block Breather Hose Assembly

2.5” Hose to 90° Fitting to 44” ½” Hose

Drain & Lower Breather Hose Assembly

90° to Y Fitting / (x2) Hoses - 15” & 21”

Comp Series Upper Breather Fitting & O-ring

M4x6mm Fasteners for Breather Top Fitting

Preinstalled

AOS Drain Fitting

Preinstalled

½” Spring Clamp

Coolant Hose Spring Clamp

Mounting Bracket

M6x12mm

Mounting Bracket

6x10mm Bolt

Mounting Bracket

” High Temp Rubber Cap

(x1) Preinstalled on AOS Can

8” Zip Tie

11” Zip Tie

Used to mount vent hose under the car

ECU Relocation Bracket

6x20mm Bolts

ECU Bracket

6mm Washers

ECU Bracket

⅜” Plastic Plug

Blocks PCV Hose

⅜” NPT to ⅝” Brass Barb Fitting

Block Breather Fitting PCV Replacement Fitting

Summary of Contents for IAG-ENG-7252





































Search results

Summary of Contents for IAG-ENG-7252

Reviews:

Related manuals for IAG-ENG-7252

Brands by name

Popular brands

IAG IAG-ENG-7252, Installation Manual

Search results

Summary of Contents for IAG-ENG-7252

Reviews:

Related manuals for IAG-ENG-7252

Brands by name

Popular brands