Thank you for purchasing i3 International’s M79 Fisheye IP dome camera.
M79 is equipped with a fisheye 1.07mm @ F2.5 lens and digital WDR, and supports
h.265 codec compression.
Note:
h.265 codec is supported by SRX-Pro v7 and above only. For backwards
compatibility, change the codec to h.264 in the camera’s web settings > Config >
Image > Video/Audio > Video Compression.
SAFETY
When installing your M79 camera be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• contaminants such as dust and smoke
• strong magnetic fields
• moisture and humidity
• areas with mechanical vibrations
• fluorescent lamps or objects that reflect light and unstable light sources
• temperatures below -30° C (-22° F) and above 50° C (122° F
).
To avoid electrical shock and to preserve the product warranty,
DO NOT
disassemble the camera. Refer servicing to qualified personnel only.
POWER SUPPLY
This camera accepts PoE power.
Ensure the supplied voltage meets the power consumption requirements of
this camera (6W) before powering the camera on. Incorrect voltage may cause
irreparable damage to the video camera and will effectively void the camera
warranty.
CLEANING
• For maximum optical clarity, the camera dome or lens must remain clean.
Use a soft, dry cloth to remove finger prints or dust from the dome cover.
• Use a blower to remove dust from the lens.
• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may
damage the surface finishes.
PACKAGE CONTENTS
Ensure that the items received match those listed on the order form and the packing
slip. In addition to this manual and a fully assembled camera, the dome camera
packing box includes:
A.
Surface Mount template x1
B.
Round Head Screw (Tapping Type) x3
C.
Plastic Anchor x3
D.
Standard RJ45 Connector x2
E.
Rubber plug x1 (block the camera’s
side cable opening in surface installations
where the cable is routed upwards instead
of through the side).
CAMERA PARTS AND DEFINITIONS
B
C
D
6MP Infrared Outdoor IP 360-degree Fisheye Camera
M79
User Manual
i3-TRNG-CAMS-
M79
.indd
Rev
. 220127
ACT Download &
Documentation
and download
AnnexxusConfigurationTool v1.9 (ACT)
.
Contact our Technical Support team at:
1.877.877.7241
or
if you have any questions
or concerns regarding camera installation or if you require
software services or support.
E
A
2
1.
Magnetic tinted plexiglass cover ring. Lift off using the notch.
2.
RJ45 Ethernet PoE Port with waterproof RJ45 connector assembly.
Insert an Ethernet cable into the port for network connection as well as PoE
(Power over Ethernet) power. To maintain water-resistant rating in outdoor
installations, make sure to use the included waterproof RJ45 Connector assembly.
3.
Rubber plug (
E
) for the side cable opening. Install when not routing the cable
through the side opening (E.g. Pendant mount installations)
4.
MicroSD Card slot for on-camera video storage (up to 128GB supported, sold
separately).
5.
Reset pinhole. Press for 10 seconds to restore camera settings to factory defaults.
6.
Grounding threaded screw hole.
7.
Mounting holes (x3)
8.
Light sensor (do not block or obstruct)
9.
Microphone
10.
IR LED lights, 65ft/20m (x6)
SURFACE INSTALLATION
Start by preparing the mounting surface. Based on installation location and surface type,
supplied screws and anchors may not be adequate.
For pendant or horizontal wall-mounting, purchase the back box (i3 part numbers: B79)
and use a 3/4” NPT pipe or DB60, respectively. Surface installation can be completed
without a back box.
Note:
After installing the camera, your network camera must be accessible from your
local network (LAN).
To complete a surface mount installation:
1.
Attach the supplied mounting template to the mounting surface.
2.
Drill 3 holes, as marked on the template, insert 3 supplied anchors into the holes.
7
7
1
5
/
8
” (41 mm)
5
1
/
8
” (130 mm)
NOT
IN
USE
Rubber plug (not to scale)
4
5
10
9
3
6
1
10
8
WATERPROOF RJ45 ASSEMBLY
To prevent the corrosion of the RJ45 connector and to maintain the camera
warranty, use the RJ45 waterproof assembly attached to the camera, as shown in
the diagram below.
1
2
3
1.
Twist off the RJ45 waterproof
assembly from the RJ45
connector.
2.
Feed the CAT5e/6 cable through
the opening in the connector and
crimp it using the standard RJ45
connector provided.
3.
Plug the crimped CAT5e/6 cable
into the RJ45 connector on the
camera and twist the waterproof
assembly on to re-attach it.
Figure 3. M79, Parts and Definitions
Figure 1. M79, Accessories
Figure 2. Waterproof RJ45 connector
