Thank you for purchasing i3 International’s IP09CP PoE extender (sold in pairs). Use IP09CP as a point-to-point PoE (Power over
Ethernet) extender to power IP devices and to carry IP signal for distances of up to 984 feet (300 meters) using existing coaxial cable
infrastructure. Use with i3’s line of IP cameras and PoE switches and/or U12 NVR (built-in PoE).
INSTALLATION
PoE over Coax Extender, 1000 ft
IP09CP
User Manual
i3-TRNG-ACCESSORIES-
IP09CP
.indd
Rev. 220913
FEATURES
• Signal extension up to 984 ft (300 m) over coaxial cable.
• Provides up to 90W power to a remote PoE device.
• Power source from either a PoE switch or an external power
adapter.
• Bandwidth up to 100Mbps.
• Supports full duplex and half duplex mode and Auto MDI/
MDI-X switching.
• Built-in 30kV ESD, 40A EFT, and 30A surge at RJ45 side.
• Note:
Ax85 supports distances up to 328 ft (100 m) only.
Mode 1 (Auto Mode, default) is recommended for all IP
devices.
PoE Cameras &
other IP devices
IP09CPT
(Transmitter)
i3 INTERNATIONAL INC.
1.866.840.0004
www.i3international.com
1
2
3 4
5
6
7
8
REGULATORY NOTICES (FCC CLASS A)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the
limits of a Class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
984 ft
300 m
6.5 ft
2 m
6.5 ft
2 m
PoE Switch /
U12 NVR
CONNECTORS
1.
DC Power Connector.
Connect to DC48~56V adapter if
connecting to a non-PoE switch.
2.
Power LED Indication.
Indicates device power status.
See Table 1.
3.
Status Indication.
Indicates RJ45 mode.
See Table 3.
4.
Status Indication.
Indicates BNC mode.
See Table 4.
5.
DIP Switch.
Mode selector.
See Tables 5, 6.
6.
RJ45 Connector.
Connect to the PoE IP device.
See Table 7.
7.
PoE LED Indication.
Indicates PoE connection status.
See Table 2.
8.
BNC Connector.
Connect to the second IP09CP device using the
RG59 cable, 984 ft (300 m) or less. The link speed is up to 100
Mbps.
Figure 2.
IP09CP front and back panels, parts description.
Note, connectors that are not labeled are reserved/not in use.
Figure 1.
IP09CP connection diagram.
RG59 / RG6U coaxial
IP09CPR
(Receiver)
PACKAGE CONTENTS
1.
IP09CPT (
Transmitter
) x1. Connect to the IP camera.
2.
IP09CPR (
Receiver
) x1. Connect to the PoE switch.
3.
Plastic Anchor x8
4.
Round Head Screw (Tapping Type) x8
Figure 3.
IP09CP front and back panels
