background image

Subject to change without notice.

Edition: 26 Feb. 2020      Ver. A0      Page 1/9

HIM38/RF    HIM39/RF

HF and PIR, 1-10V Dimming / Independent DALI Control with RF Wireless

IP65 High Bay Dual Sense Sensor

TM

Stand-by power

EMC standard (EMC)
Safety standard (LVD)

Certification

Radio Equipment (RED) 

Resistive

HC034RF (IP20)

HIM39/RF

EN55015, EN61000

Semko, CB, CE , EMC, RED, RCM

EN60669, AS/NZS60669

Model No.

HIM38/RF   HIM39/RF

120

~

277VAC  50/60Hz 

Mains voltage

Load ratings:

EN300440, EN300328, 

EN301489

<1.5W

Input Characteristics 

Safety and EMC

400VA@120V;800VA@220-277V

800W@120V;1600W@220-277V

400VA (capacitive); 1200W (resistive)

max. 20 devices, max. 40mA

Capacitive

Sensor & RF Data

Operation temperature

Ta: -20

O

C ~ +50

O

C

Environment 

IP65

IP rating

Model No.

<0.2mW (HF)

5.8GHz +/- 75MHz (HF)

High Frequency (microwave), PIR 

Sensor principle 

Operation frequency

Transmission power

Detection range
Detection angle
RF frequency

RF transmission distance

Max. (

 

O

 

x H) 18m x 15m

868MHz (FSK mode, default)

30m indoor, 50m outdoor

30s

Warming-up

Technical Data

360

O

4 modes: PIR, HF, PIR+HF, PIR/HF

Sensor mode

Mechanical Structures and Installations

For more details, please refer to user manual.

HIM38/RF   HIM39/RF

IP65

RED

Sensor module

PIR

LED indicator

Infrared receiver

Rotary switch for programing

Cable entry

Installation rack

A. Ceiling mount

Daylight sensor

81.5

4.1

66.6

91.5

80.7 75

4.1

59.3

73.5

57.3

47.5

24.5

Summary of Contents for HIM38/RF










Reviews: