background image

Q2SSNM4SPA

Medium Temperature 

Self Contained 

P/N 3091736_C

October 2020

Installation & 

Operation Manual

®

Æ

Spanish 3091737

WARNINGS:

If  the information in these instructions are not followed 
exactly, a fire or explosion may result, causing property 
damage, personal injury or death.

Installation and service must be performed by a qualified 
installer or service agency.

READ THE ENTIRE MANUAL BEFORE 
INSTALLING OR USING THIS EQUIPMENT.

The unit uses R-290 (propane) gas as the refrigerant. 
R-290 (propane) is flammable and heavier than air. It 
collects first in low areas but can be circulated by the 
fans. If  propane gas is present or even suspected, do not 
allow untrained personnel to attempt to find the cause. 
The propane gas used in the unit has no odor. The lack 
of  smell does not indicate a lack of  escaped gas. If  a 
leak is detected, immediately evacuate all persons from 
the store, and contact the local fire department to advise 
them that a propane leak has occured. Do not let any 
persons back into the store until the qualified service 
technician has arrived and that technician advises that it 
is safe to return to the store. No open flames, cigarettes 
or other possible sources of  ignition should be used 
inside or in the vicinity of  the units.

FAILURE TO ABIDE BY THIS WARNING COULD 
RESULT IN AN EXPLOSION, DEATH, INJURY AND 
PROPERTY DAMAGE.

IMPORTANT
Keep in store for future reference!

MANUAL-SELFCONTAINED Q2SSNM4SPA

Summary of Contents for Q2SSNM4SPA





























Reviews: