background image

® U.S. Registered Trademark
Copyright © 2002 Honeywell •   

 • All Rights Reserved 

INSTALLATION INSTRUCTIONS

69-1507-2

T8602D Chronotherm

® 

IV

Deluxe Programmable

Thermostats

APPLICATION

The T8602 Chronotherm 

®

 IV Deluxe Programmable Thermostat provides electronic control of 24 Vac single-stage 

heating and cooling systems or 750 mV heating and 24 Vac cooling. Refer to Table 1 for a general description of the 
thermostat. All T8602 thermostats are powered by batteries.

Table 1. Description of T8602 Thermostats.

MERCURY NOTICE

If this control is replacing a control that contains 
mercury in a sealed tube, do not place your old 
control in the trash. Dispose of properly.

Contact your local waste management authority 
for instructions regarding recycling and the 
proper disposal of the old control. 

INSTALLATION

When Installing this Product...

1.

Read these instructions carefully. Failure to follow 
the instructions can damage the product or cause 
a hazardous condition.

2.

Check the ratings given in the instructions and on 
the product to make sure the product is suitable for 
your application.

3.

Installer must be a trained, experienced service 
technician.

4.

After completing installation, use these instructions 
to check out the product operation.

Location

Install the thermostat about  5 ft (1.5m) above the floor in 
an area with good air circulation at average temperature. 
See Fig. 1.

Do not install the thermostat where it can be affected by:
— drafts, or dead spots behind doors and in corners.
— hot or cold air from ducts.
— radiant heat from sun or appliances.
— concealed pipes and chimneys.
— unheated (uncooled) areas such as an outside wall 

behind the thermostat.

Wallplate Installation

The thermostat can be mounted horizontally on the wall 
or on a 2 in. x 4 in. (50.8 mm x 101.6 mm) wiring box. 
Position wallplate horizontally on the wall or on a 
2 in. x 4 in. (50.8 mm x 101.6 mm) wiring box.

T8602

System

Changeover

System Selection

Fan

Selection

Comments

D

Heat-Cool

Automatic

Heat-Off-Cool-Auto

On-Auto

System and fan selections are made on 
keyboard.

Summary of Contents for T8602D













Reviews: