![background image](http://html.mh-extra.com/html/honeywell/5820l-slim-line-wireless-door-window-transmitter/5820l-slim-line-wireless-door-window-transmitter_installation-and-setup-manual_154916001.webp)
K9232V1 10/05 Rev. A
ADEMCO 5820L
Door/Window Contact Transmitter
Door/Window Contact Transmitter
Door/Window Contact Transmitter
Door/Window Contact Transmitter
INSTALLATION AND SETUP GUIDE
GENERAL INFORMATION
The 5820L is a single-zone Slim-Line Door/Window
contact transmitter that provides wireless
notification of intrusion. The 5820L can be used
only with alarm systems that support 5800 Series
wireless devices. The 5820L has its own unique
serial number permanently assigned during
manufacture. You must enroll the transmitter’s
serial number in the control panel before it will
operate in the system. Refer to the control panel’s
installation instructions for programming details.
Note:
During programming of the control panel,
5820L transmitters must be enrolled as Input Type
3 (Supervised RF), Loop 1.
The transmitter is powered by one AAA Lithium (or
alkaline) battery that is easily replaced when a low
battery condition is indicated by the control panel.
TAMPER PROTECTION
Front and back-case tamper is provided using the
same switch. The front-case tamper is always
enabled. Adding the third screw as shown in Figure
2 enables the back-case tamper.
MAGNET
OPENING
SLOT
GAP
0.5" MAX
5820-001-V0
MAGNET ALIGNMENT
LOCATORS
Figure 1. 5820L (Typical Installation Arrangement)
+
MOUNTING
HOLE
MOUNTING
HOLE
TAMPER
PROTECTION
5820-002-V1
BATTERY
(1.5VDC, AAA
LITHIUM OR
ALKALINE)
TAMPER
SWITCH
Figure 2. 5820L Mounting/Battery Location
MOUNTING
The description that follows assumes that the
transmitter will be mounted as shown in Figure 1,
with the magnet located adjacent to the unit's left
side. The transmitter may, however, be installed in
any
direction, as long as the relationship of the unit
to the magnet is maintained as shown in Figure 1.
1.
Temporarily
mount the 5820L and magnet
using the double-back tape supplied.
Note:
Before mounting the transmitter and magnet
permanently
using the double-back tape or
mounting screws, conduct a
Go/No Go
test (see
control's instructions) to verify adequate signal
strength and reorient or relocate the transmitter if
necessary.
2.
If the
Go/No Go
test was successful,
remove
the transmitter's cover
by inserting the flat
blade of a small screwdriver into the opening
slot at one end of the unit as shown in Figure 1,
and separating the two halves.
3.
The 5820L must only be mounted against a
flat
surface. A curved surface would cause undo
stress to the unit and possible failure to operate
properly.
4.
Install
mounting
screws in the two outside
mounting holes as shown in Figure 2 using a #1
Phillips.
5.
If the case-back tamper switch will be used,
install a third screw in the
middle
hole.
6.
Mount
the magnet (supplied) adjacent to the
two vertical positioning lines on the case side
(see Figure 1). The gap can be one-half an inch
maximum.
7.
To
reinstall
the cover, position the cover so
that it covers the mounted case-back, and snap-
shut. The two case halves can only be fitted
together in one direction.
Note:
Do
NOT
attempt to remove the PCB from the
plastic cover for any reason.
BATTERY
INSTALLATION/REPLACEMENT
Replace battery only with same or equivalent type.
Dispose of used batteries according to the battery
manufacturer’s instruction.
1.
Remove the transmitter's cover
(if it is not
off already) as described in
Mounting;
step 2.
2.
Observe correct polarity and insert the
battery
provided into the battery retainer clips
as shown in Figure 2.
Note
:
Replace
battery
only
with type specified in
the Specifications paragraph.