Home Easy HE-106, Manual

Page: 1 / 3

1 6 5 4 3 2
1 2 3 4 5 6 7
C H Byron
34, Sherwood Rd
Aston Fields
Bromsgrove
B60 3DR
Contact Details:
433MHz
R&TTE
APPROVED
CH Byron Electrical United Kingdom. www.chbyron.com
A
B
DK
FIN
F
D
GR
LT
IRL
I
L
NL
P
E
S
UK
BG
CZ
EST
H
IS
LV
M
N
SK
SLO
CH
PL
RO
Tel: 0845 2301231
Fax: 01527 557701
Web: www.chbyron.com
E-mail:
support@chbyron.com
Help: Occasionally interference from receiver sockets plugged into adjacent wall
sockets or used with transformers (low voltage products) can affect the operating
Try placing one of the receiver sockets in another wall socket. For low voltage
products, place the transformer as far away form the receiver socket as possible.
RF Range
HE-106 Remote Control
Door Release
V1.0
The HE-106 Remote control Door Release allows
to you unlock and allow access control to a
variety of aluminium, timber and steel doors.
Simply press the button to unlock your door
Compatible with HE100, HE,101, HE301
-HE300, H301, HE303, HE307 & HE308
Suitable for right, left, inward and
outward opening doors.
-Fail Lock Operation
-30 Metre Range
-Automatic Relock
Contact: Helpline: 0845 2301 231
The radio signals operating distance is reduced when the signal has to
pass through walls. The radio signal achieve a range of 30m inside a
building; this can be reduced depending on the type of material
HOME
easy
Set-Up Diagram:
The group setting allows you to switch "On/Off"
multiple receiver sockets/modules in one simple press.
To set a receiver to the group setting, set the receiver
into the learn mode as normal (see instructions Learn
Mode) and press group(G) On.
The socket will now switch On/Off with the group buttons; this stays the same
even if the group slide switch is on I, II, III or IV.
The receiver sockets/modules can still be used individually using the normal
On/Off buttons.
SX37
HE-106
ON
SX37
12V DC Power
T
12V AC~300mA (Not Included)
Installation:
HE106 Door Release:
First select a suitable location for the HE-106 door release unit, it's recommended
that HE-106 is not placed in direct sources of sunlight, heat and onto metallic
surfaces, as this will the effect the operating performance.
Before fitting the door release unit, test the unit to make sure the location is suitable
e.g. operating the unit through an external wall will reduce the operating range, if
required move the unit close to the external wall. The HE-106 is an accessory product
The HE-106 is an accessory product for the HomeEasy
range of products, additional units are required for the
unit to operate.
1: The HE-106 base plate, can be attached using either the self adhesive strip or screws.
1: The HE-106 can be attached using either the self adhesive strip or screws (included)
2: Clip the HE-106 on
the base plate using
the key-hole slots.
3: Connect the power adapter into the terminal
connection "1" and "2" as per the diagram.
Terminal 1 + wire
Terminal 2
- wire
Posative Negative
4: Plug the SX37 power adapter into a standard 13amp
socket, the HE-106 will beep twice and the LED will flash to
indicate that the power is connected. Now program a
HomeEasy remote control to the HE-106 unit (Remote
Control Not Included).
-See Pairing/Deleting Remote Control
5: Install the HomeEasy Door Lock into the door frame, making sure the location
and orientation is correct for the door. The HomeEasy Door lock is powered by a
12VAC -300mA transformer, connect one terminal from the transformer to one of
the terminals on the door lock.
T
12V AC~300mA (Not Included)
Door
Lock