Himmelstein 2270V Installation And Operation Manual Download

Page: 1 / 12

S. Himmelstein and Company

Strain Gage Reaction Torquemeters Installation Guide

INSTALLATION AND OPERATION GUIDE FOR HIMMELSTEIN

STRAIN GAGE REACTION TORQUEMETERS

AND

TORQUE TRANSFER STANDARDS

WITH BOTH ANALOG AND DIGITAL OUTPUTS

Applies To Models 2270V, 2280V, 2286V, 2287V, CF2800V AND 2300DV

Customer:
Model Number:

Serial Number:

Factory Reference Number:
Rated Torque (lbf-in):
Torque Overload Capacity (lbf-in):

Factory Settings

Analog Output: ±10.000V at Rated Torque:
Filter Cutoff Frequency (Hertz):
Digital Output Units of Measure:
Special Features:

Readout/Power Supply Furnished:

( ) Yes

( ) No

If Yes, Readout Model Number:
Interconnect Cable P/N:

Furnished:

( ) Yes

( ) No

Calibration Data is listed in the attached Calibration Certificate

S. Himmelstein and Company

Designing and Making the Worlds' Best Torque Instruments since 1960

2490 Pembroke Avenue, Hoffman Estates, IL 60169 USA • Tel: 847-843-3300 • Fax: 847-843-8488 • www.himmelstein.com

Summary of Contents for 2270V













Search results

Summary of Contents for 2270V

Reviews:

Related manuals for 2270V

Brands by name

Popular brands

Himmelstein 2270V, Installation And Operation Manual

Search results

Summary of Contents for 2270V

Reviews:

Related manuals for 2270V

Brands by name

Popular brands