Hearth and Home Technologies 350TRSI-AUF Скачать руководство пользователя

Страница: 1 / 79

Heat & Glo • 350TRSI-AUF, 350TRSILP-AUF • 2089-980 Rev. C • 10/10

Models:
350TRSI-AUF
350TRSILP-AUF

Owner’s Manual

Installation and Operation

•

DO NOT

USE OR STORE FLAMMABLE

MATERIALS NEAR THIS APPLIANCE.

•

DO NOT

SPRAY AEROSOLS IN THE VICIN-

ITY OF THIS APPLIANCE WHILE IT IS IN
OPERATION.

• What to do if you smell gas

DO NOT

try to light any appliance.

DO NOT

touch any electrical switch.

NOT

use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s
instructions.

- If you cannot reach your gas supplier, call

the fi re department.

• Installation and service must be performed

by a qualifi ed installer, service agency, or the
gas supplier.

WARNING: If the information in these

instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury, or death.

WARNING

This appliance has been supplied with an integral barrier
to prevent direct contact with the fi xed glass panel. DO
NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.

HOT SURFACES

Glass and other surfaces are hot during
operation AND cool down.

Hot glass will cause burns.

•

DO NOT

touch glass until it is cooled

• NEVER allow children to touch glass
• Keep children away

• CAREFULLY SUPERVISE children in same room as

fi replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other fl ammable
materials.

• DO NOT

PLACE ARTICLES ON OR AGAINST THIS

APPLIANCE.

• Keep clothing, furniture, draperies and other fl ammable

materials away.

SAI Global

Ref No GSCS20162

AS4553:2008

This is a room sealed appliance and no other ventilation is
required than what is provided.

DO NOT DISCARD THIS MANUAL

NOTICE

• Leave this manual with

party responsible for use
and operation.

DO NO

DISCARD

• Important operating

a n d m a i n t e n a n c e
instructions included.

• Read, understand and follow

these instructions for safe
installation and operation.

Содержание 350TRSI-AUF
















































































Результаты поиска

Содержание 350TRSI-AUF

Отзывы:

Похожие инструкции для 350TRSI-AUF

Бренды по названию

Популярные бренды

Hearth and Home Technologies 350TRSI-AUF, Руководство пользователя

Результаты поиска

Содержание 350TRSI-AUF

Отзывы:

Похожие инструкции для 350TRSI-AUF

Бренды по названию

Популярные бренды