background image

Thank you for purchasing the SuperPole System. We are
confident that you will find the unique design and durable
construction of this HealthCraft product to be of great assistance
in your daily routine.

To fully enjoy your SuperPole System, please take a few moments
to read these instructions. You should store these instructions in a
safe place for future reference.

CAUTION:

IMPORTANT:

NOTE:

It is your responsibility to see that your SuperPole

System is properly assembled, installed, and cared for. Failure
to follow instructions in this manual could result in serious injury.

The SuperPole System should only be used in

locations where the floor and ceiling surfaces are structurally
sound. It should not be installed on loose floor coverings, in
rooms with radiant ceiling heating, in mobile homes or with
suspended or angled ceilings. Recommended weight limit is
250 lb. Not more than 150 lbs should be exerted on trapeze
handle (sitting up assistance only). If you are not equipped to
undertake the outlined work, we would recommend that you
have your SuperPole System installed by a qualified contractor.
The extension screw feature of the SuperPole System can
generate enough force to damage a ceiling. Exercise caution
when tightening this screw.

It is recommended that the ceiling anchor plate be

installed to span across two joists in a ceiling as shown below.
In cases where this may not be possible (i.e. one joist only), be
sure to test the pole rigorously after installation to be certain of
a secure installation.

We strongly recommend that you give thought as to the optimal
location of your SuperPole System before installation. The
following questions may help you to decide upon a location:

a. What motions will you be going through? (pulling up to
standing, lowering to sitting, transferring from chair to toilet,
etc.)

b. Where will you need the most support? (while walking, while
lifting, etc.)

c. What is your strongest side/hand?

d. What is your complete transfer path? Will the location allow
for full support over most of your path of motion?

e. Will the pole be far enough away to allow you to stand
comfortably?

Locate pole adjacent to hip/belt line and
as close to bed as possible while
allowing clearance for bed coverings. If
using SuperBar option, you will need to
set the pivot locking positions of the
bar. As a suggestion, positions A and E
are good for moving in bed, B for
pulling up to sitting, C for pulling up to
standing and D for transferring out of
bed.

Toilet

Bathtub only

- locate pole between three to

ten inches forward of the knees and
two to six inches to side of knees when
seated.

- locate pole

base against tub, approximately half
way along its length. If using SuperBar
option, you will need to set the pivot
locking positions of the bar. As a
suggestion, positions B or D are
suitable for standing from toilet, C and
F for transferring into bathtub, E and D
for transferring out of bathtub.

Locate pole between three to ten
inches forward of the knees and two to
six inches to side of knees when
seated. If using SuperBar option, you
will need to set the pivot locking
positions of the bar. As a suggestion,
positions A or C are suitable for
standing assistance, while D and E are
suitable for completing a transfer to a
nearby walker or wheelchair. Position
B provides side support if this is
preferred for standing.

CAUTION:

IMPORTANT:

The SuperPole System can loosen due to settling

of the floor or ceiling, particularly in the first hours and days
following installation. As a result, we recommend that you test
that the pole is secure, and the extension screw tightened if
needed during this time, and then on a monthly basis.

Use of screws in ceiling anchor plate

- The

ceiling anchor plate has two holes that may be used to
accommodate screws to better anchor this plate directly to the
ceiling or ceiling joists. It is strongly recommended to install
screws to prevent slippage in the following situations:

1. You expect to subject the pole to heavy usage such as when
the pole is used for more than mild support for side to side
stability.

2. You are not able to inspect, or have inspected (and tighten if
neccessary) the extension screw on a monthly basis.

Thank You . . .

Thank You . . .

Safety Considerations

Safety Considerations

Getting Started . . .

Getting Started . . .

Ceiling

Joists

Pole

Anchor Plate
spanning
across 2 joists

Installation Instructions

Models SPS, SPB, STP

www.healthcraftproducts.com

The

System

SuperPole

Bed

A

B

B

B

E

A

D

D

E

A

C

C

F

C

E

D

Bathtub and/or Toilet

Chair

ealth

Craft

H

TM

Summary of Contents for SP-S

Page 1: ...ne and as close to bed as possible while allowing clearance for bed coverings If using SuperBar option you will need to set the pivot locking positions of the bar As a suggestion positions A and E are good for moving in bed B for pulling up to sitting C for pulling up to standing and D for transferring out of bed Toilet Bathtub only locate pole between three to ten inches forward of the knees and ...

Page 2: ...he anchor plate contact the ceiling The anchor plate must be made to contact the ceiling squarely This can be facilitated by having a second person hold the pole exactly vertical while turning the extension screw Continue turning the extension screw until the anchor plate contacts the ceiling squarely From this point continue to turn the extension screw approximately two to five turns until the Su...

Page 3: ...r is important in two ways first the height at which you fix the grooved collar determines the height of the SuperBar hand rail unit 10 and secondly each of the grooves correspond to a rotational locking position of the hand rail unit refer to figure B3 You will want to fix the grooves to have the hand rail lock in the most advantageous positions for your assistance as discussed on page 1 Getting ...

Page 4: ...Testing the location Have the user gently try the installed location of the trapeze handle and pole Ensure that the trapeze handle is not too close to allow a comfortable sit up action Should the trapeze support arm need to be moved remove the set screw installed in step C6 and lift the support arm up by at least one inch and reinstall the screw with the arm at a new angle to avoid the set screw b...

Reviews: