![background image](http://html.mh-extra.com/html/hatteras-hammocks/single-swing-with-oak-arms/single-swing-with-oak-arms_assembly-instructions_2107370001.webp)
Weight limit: 350 pounds
YOUR BOX SHOULD CONTAIN:
1 - Single Swing Cushion
1 - Oak Top Stick (4 Sided)
1 - Oak Bottom Stick (5 Sided)
1 - Oak Spreader Bar
2 - Curved Oak Arms
2 - Chain and Ring Assemblies
1 - Hanging Bracket Assembly
1- Bracket
2 - Lag Bolts 2” x ¼”
1 - S-Hook
1 - Hardware Pack:
2 - Carriage Bolts 3” x 3/8”
2 - Carriage Bolts 2½” x 3/8”
2 - Carriage Bolts 1¼” x 3/8”
10 - Nuts 3/8”
14 - Washers 3/8”
Before beginning assembly,
check that you have all parts!
Single Swing With Oak Arms
Congratulations on your purchase of a Hatteras Hammocks
®
Single Swing With
Oak Arms! We believe you’ll find it to be a product of unsurpassed quality, dura-
bility and relaxation potential, a source of enjoyment for you and yours for years
to come. Once assembled, your new swing may be hung from a wooden beam
sturdy enough to support at least 350 pounds, or from one of the quality swing
stands that we offer.
ASSEMBLY INSTRUCTIONS
NOTE: If you plan to hang your Hatteras Hammocks® Single Swing With Oak Arms
on a swing stand, it’s a good idea to assemble the stand, according to its instruc-
tions, before beginning assembly of your swing itself.
STEP 1. Insert the Oak Top Stick through the top fabric sleeve at the back of the Single
Swing Cushion (the sleeve attached to the smallest section of cushion). Next, slide the
Oak Bottom Stick into the fabric sleeve at the bottom front of the cushion (the sleeve at-
tached to the largest section of cushion). The narrowest part of the
Oak Bottom Stick should be facing upward (into the curve of the
Curved Oak Arm, once you install it); improper positioning can lead
to chafing and tearing of cushion fabric.
STEP 2. To connect the Curved Oak Arms, first position each arm so
the end with the two holes is at the top (
FIGURE 1
). Next, insert (from
front to back) a 2½” Carriage Bolt through the Curved Oak Arm’s
topmost hole, and then through the second hole from the end on
the Oak Top Stick (
FIGURE 2
). Add first a Washer and then a Nut to
the end of the bolt, hand-tightening only.
STEP 3. To connect the other end of the same Curved Oak Arm to
the Oak Bottom Stick, insert (from front to back) a 3” Carriage Bolt
through the single hole at the bottom of the arm, and then also
through the second hole from the end on the Oak Bottom Stick
(
FIGURE 3
). Add first a Washer and then a Nut to the end of the bolt,
hand-tightening only.
Questions about our
products? Please call our
toll-free customer service
line at (800) 643-3522.
Visit us online at
hatterashammocks.com.
PARTS LIST
TOOLS YOU’LL NEED:
9/16” wrench or socket,
or adjustable wrench
(not included)
NOTE:
If you’re
NOT
hanging
your swing from a Hatteras
Hammocks® swing stand and
instead are installing it onto a
wood beam or tree limb, you’ll
need a few additional tools
(also not included):
ADDITONAL TOOLS:
• 7/16” wrench or socket,
or adjustable wrench
• Drill with ¼” bit
• Sharpened pencil
Instructions continue on back of page
FIGURE 3
FIGURE 2
FIGURE 1