background image

M O B I L I T Y

M O

B I L

I T Y

M O

B I L

I T Y

AL010 MICRO SCOOTER LIFT

AL030 POWER TOTE MANUAL WHEELCHAIR LIFT

INSTALLATION GUIDE & OWNER'S MANUAL

AL010 Micro Scooter Lift

AL030 Power Tote for Manual Wheelchairs

Congratulations on your new lift purchase.  The Micro Scooter Lift and Power Tote are two of the easiest
and most trouble free ways to transport your chair or scooter.  This manual is written to be used both as an installation
guide as well as an operation guide for the end user for both the AL010 Micro Scooter Lift and AL030 Manual Wheel-
chair Lift.  Refer to the index below for the sections that apply to your lift and options.  

Please read the manual thoroughly BEFORE attempting any installation

adjustment or use of the lift.

  

Both installers and operators should familiarize themselves with this entire manual.
The manual will be divided into the following sections for easy reference;

Section  1   -  Unpacking the Lift

Section  3   -  Vehicle Preparation
Section  4   -  Installing the Lift ( No Swing Away )
Section  5   -  Installing the Lift ( with Swing Away Option )
Section  6   -  Operating the AL105 Swing Away Option
Section  7   -  Operating the AL010 Micro Scooter Lift
Section  8   -  Operating the AL030 Power Tote Lift
Section  9   -  Adjusting the AL010 and AL030
Section 10  -  Safety & Maintenance
Section 11  -  Troubleshooting Guide

If you have any questions or comments concerning the installation or operation of your scooter/chair lift, please 
contact your local distributor for additional technical information.  

Only authorized dealers should install this lift.

Section  2   -  Wiring the Vehicle

Caution: 

Some scooters and chairs may be unsuitable for transport in or on a motor 

vehicle.  Please contact the manufacturer of your mobility device to determine its transportability

.  

Summary of Contents for AL010

















Reviews: