Harman PELLET P61A Installation And Operating Manual Download | Manualshive

Page: 1 / 36

background image

3-90-05822R29_JR15_04/14

save these instructions.

installation & operating Manual

saFetY notice

Please read this entire Manual beFore You install and use Your new rooM heater. Failure to

Follow instructions MaY result in ProPertY daMage, bodilY injurY, or even death.
For use in the u.s. and canada. suitable For installation in Mobile hoMes.
iF this harMan stove is not ProPerlY installed, a house Fire MaY result. For Your saFetY, Follow

installation directions. do not use MakeshiFt coMProMises.
contact local building or Fire oFFicials about restrictions and installation insPection
reQuireMents in Your area.
contact Your local authoritY (such as MuniciPal building dePartMent, Fire dePartMent, Fire

Prevention bureau, etc.) to deterMine the need For a PerMit.
cette guide d'utilisation est disPonible en Francais. chez votre concessionnaire de harMan®.

Model(s):

P61A Freestanding Pellet Stove

NOTICE: SAVE THESE INSTRUCTIONS

hot glass will cause burns.

•  Do not touch glass until it is cooled
•  NEVER allow children to touch glass
•  Keep children away
•  CAREFULLY SUPERVISE children in same room as

stove.

• Alert children and adults to hazards of high temperatures.

high temperatures may ignite clothing or other

flammable materials.

• Keep clothing, furniture, draperies and other flammable

materials away.

hot surFaces!

Glass and other surfaces are hot during

operation and cool down.

WARNING

!

To obtain a French translation of this manual, please

contact your dealer or visit www.harmanstoves.com

Pour obtenir une traduction française de ce manuel, s’il

vous plaît contacter votre revendeur ou visitez www.

harmanstoves.com

note

Contact your local dealer with questions on installation,

operation or service.

Service parts list has been removed from this manual.

Refer to Owner’s Manual or Individual service parts list.

1
2
3
...
»

Summary of Contents for PELLET P61A





































Reviews:

No comments

Related manuals for PELLET P61A

Brand: Teba Pages: 10

Brand: Morso Pages: 24

Brand: Harman Pages: 18

Brand: Drop Pages: 21

Brand: F2 Fires Pages: 16

Brand: Aga-Rayburn Pages: 8

Brand: De Vielle Pages: 8

SURVIVOR LIFESTYLE 12-RS

Brand: England's Stove Works Pages: 9

Brand: Englander Pages: 37

Brand: England's Stove Works Pages: 37

Brand: Englander Pages: 42

Brand: England's Stove Works Pages: 51

Brand: England’s Stove Pages: 57

Brand: Logaire Pages: 12

Brand: Monessen Hearth Pages: 28

Brand: Bosca Pages: 48

Brand: Nordica Pages: 108

Brand: Palazzetti Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands