background image

Harman®  •  P35i-C Owner’s Manual_R3  •  2019 -___  •  03/20

1

8390-784C

To obtain a French translation of this manual, please 

contact your dealer or visit www.harmanstoves.com

Pour obtenir une traduction française de ce manuel, s’il 

vous plaît contacter votre revendeur ou visitez www.

harmanstoves.com

NOTE

Owner’s Manual

Care and Operation

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

Contact your local dealer with questions on installation, operation or service.

Model(s):

P35i-C Pellet Insert

NOTICE: SAVE THESE INSTRUCTIONS

Please read this entire manual before 

installation and use of this pellet fuel-

burning room heater. 

Failure to follow these instructions could 

result in property damage, bodily injury 

or even death.

•   Do not store or use gasoline or other flammable vapors 

and liquids in the vicinity of this or any other appliance.

•   Do not overfire - If any external part starts to glow, you 

are overfiring. Reduce feed rate. Overfiring will void 

your warranty.

•   Comply with all minimum clearances to combustibles 

as specified. Failure to comply may cause house fire.

WARNING

!

Hot glass will cause burns.

•  Do not touch glass until it is cooled

•  NEVER allow children to touch glass

•  Keep children away

•  CAREFULLY SUPERVISE children in same room as 

stove.

•  Alert children and adults to hazards of high temperatures.

  High temperatures may ignite clothing or other 

flammable materials.

•  Keep clothing, furniture, draperies and other flammable 

materials away.

HOT SURFACES!

Glass and other surfaces are hot during 

operation and cool down.

WARNING

!

Tested and approved for wood pellets only burning of 

any other type of fuel voids your warranty. When burning 

higher ash content pellets more frequent cleanings may 

be required.

CAUTION

!

Check building codes prior to installation.

•  Installation MUST comply with local, regional, state and 

national codes and regulations.

•  Contact local building or fire officials about restrictions 

and installation inspection requirements in your area.

CAUTION

!

Summary of Contents for P35i-C

























Reviews: