![background image](http://html2.mh-extra.com/html/hanyoung-nux/tf4/tf4_instruction-manual_3754548001.webp)
Please read the safety information carefully then use the product correctly.
The alerts declared in the manual are classified into
Danger
,
Warning
and
Caution
according to their importance
▍Safety information
28, Gilpa-ro 71beon-gil,
Michuhol-gu, Incheon, Korea
TEL : +82-32-876-4697
http://www.hynux.com
HANYOUNGNUXCO.,LTD
Digital Timer
TF4
Thank you for purchasing Hanyoung Nux products.
Please read the instruction manual
carefully before using this product, and use the product correctly.
Also, please keep this instruction manual where you can see it any time.
MD0306KE190925
INSTRUCTION MANUAL
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in minor injury or property damage
• Any use of the product other than those ecified by the
manufacturer may result in personal injury or property
damage.
• If there is a possibility that a malfunction or abnormality
of this product may lead to a serious accident to the system,
install an appropriate protection circuit on the outside.
• Since this product is not equipped with a power switch
and fuse, install them separately on the outside.
(fuse rating: 250 VAC 0.5 A).
• Please supply the rated power voltage, in order to
prevent product breakdowns or malfunctions.
• To prevent electric shocks and malfunctions, do not
supply the power until the wiring is completed.
• The product does not have an explosion-proof structure,
so avoid using it in places with flammable or explosive
gases.
• Never disassemble, modify, process, improve or repair
this product, as it may cause abnormal operations,
electric shocks or fires.
• Please disassemble the product after turning OFF the
power. Failure to do so may result in electric shocks,
product abnormal operations or malfunctions.
• Please use this product after installing it to a panel,
because there is a risk of electric shock.
• The contents of this manual may be changed without prior notification.
• Please make sure that the product specifications are the same as you ordered.
• Please make sure that there are no damages or product abnormalities occurred during shipment.
• Please use the product in places where corrosive gases (especially harmful gases,
ammonia, etc.) and flammable gases are not generated.
• Please use the product in places where vibrations and impacts are not applied directly.
• Please use the product in places without liquids, oils, chemicals, steam, dust, salt, iron, etc.
• Please do not wipe the product with organic solvents such as alcohol, benzene, etc.
(use neutral detergents).
• Please avoid places where large inductive interference, static electricity, magnetic
noise are generated.
• Please avoid places with heat accumulation caused by direct sunlight, radiations, etc.
• Please use the product in places with elevation below 2000 m.
• When water enters, short circuit or fire may occur, so please inspect the product
carefully.
• When there is a lot of noise from the power, we recommend to use insulation transformer
and noise filter. Please install the noise filter to a grounded panel, etc. and make the
wiring of noise filter output and power supply terminal as short as possible.
• Tightly twisting the power cables is effective against noise.
• Do not wire anything to unused terminals.
• Please wire correctly, after checking the polarity of the terminals.
• When you install this product to a panel, please use switches or circuit
breakers compliant with IEC60947-1 or IEC60947-3.
• Please install switches or circuit breakers at close distance for user convenience.
• We recommend regular maintenance for the continuous safe use of this product.
• Some components of this product may have a lifespan or deteriorate over time.
• The warranty period of this product, is 1 year, including its accessories, under
normal conditions of use.
• The preparation period of the contact output is required during power supply.
If used as a signal to external interlock circuit, etc. please use a delay relay together.
• The input/output terminals are subject to electric
shock risk. Never let the input/output terminals come
in contact with your body or conductive substances.
DANGER
WARNING
CAUTION
Model
Code
Content
TF4-
□
□
□
□
Digital Timer (DIN 48 ㎜ × 48 ㎜)
Time
specification
A
999.9s / 9999s
B
9m 59.9s / 59m 59s
C
999.9m / 59h 59m
Display
U
Up display
D
Down display
Input voltage
A
100 - 240Va.c. 50/60Hz
D
24 - 60Vd.c.
Control output
R
Relay output
T
Open collector output
▍Suffix code
▍Specification
Power voltage
100-240Va.c. 50/60Hz (AC), 24-60Vd.c. (DC)
Voltage fluctuation rate
Power voltage ±10 %
Power consumption
Approx. 4.8 V A / 0.7 W (24Vd.c.)
Reset
Power reset : Minimum power open time 0.5 s
Inhibit
External reset or Inhibit : Minimum input signal width 0.02 s
Control
output
Contect output
250Va.c. 3 A Resistive load (COS φ=1)
Contectless output
Open collector 30Vd.c. 100 mA Max.
Repetition of operating time
Min ±0.01 % ±0.05 s (In case of power start)
Min ±0.005 % ±0.003 s (In case of reset)
(Percentage for Setting value)
Setup error
Effect of voltage
Effect of temperature
Installation method
Panel mounting method
Operating method
Up, Down operation
Operation Mode
N mode
Reset method
Power reset, Manual reset
External connection method
8 pin socket
Input signal
method
Contect output
Open of contect, Input by short-circuit
Contectless output
Input ON/OFF of Open collector transistor
Control
output
Relay
Time limit 1c, 250Va.c. 3 A (Resistive load)
Transistor
Open collector 30Vd.c. 100 mA max.
Display
7 Segment LED (Character Height: 11 ㎜ , Character Width: 8 ㎜)
Processing
direction of digit
Up display
Up from 0 to Setting value
Down display
Down from Setting value to 0
Decimal system
999.9s / 9999s (selected by the front dip switch)
Sexagesimal system
9m 59.9s / 59m 59s (selected by the front dip switch)
999.9m / 59h 59m
Insulation resistance
Min.100 ㏁
(Based on 500Vd.c. mega Part of conduction terminal and exposured non-electrified metal part)
Dielectric strength
2000Va.c. 50/60 Hz for 1 minute (Electric conduction part and disclosed non-electrically
chargeable metal part)
Noise immunity
Square-wave by noise simulator ±2 KV (between operational power terminals)
Vibration
Destruction
10 - 55 Hz (for 1 minute) single amplitude 0.75 ㎜ X · Y · Z each direction, 2h
Malfunction
10 - 55 Hz (for 1 minute) single amplitude 0.5 ㎜ X · Y · Z each direction, 2h
Shock
Destruction
300 m/s
2
(30G) X · Y · Z each direction, 3 times
Malfunction
100 m/s
2
(10G) X · Y · Z each direction, 3 times
Relay
life time
Mechanical
Min 10,000,000 times
Electrical
Min 100,000 times (250Va.c. 3 A Resistive load)
Ambient temperature &humidity
0 ~ 50 ℃ , 35 ~ 85 % RH
Storage temperature
-20 ~ 65 ℃
Weight(g)
Approx. 100
▍Part names
■ Dimension
▍Connection diagram
■ Contect control output
1s
0.1s
1m
0.1m
1s
0.1s
Processing time
Manual reset
switch
0.1s/1s selection switch
999.9s / 9999s(A type)
9m 59.9s / 59m 59s(B type)
999.9m / 59h 59m (C type)
Output Indicator
Time setting
switch
▍Dimension & Panel cutout
[Unit:mm]
0.1s
1s
0.1s
1s
■ Contectless control coutput
▍Operation chart
Mode
Up
N
Down
Operation after TIME-UP
Keep the output or display until the time when the reset is input.
■ Panel cutout
■ Up display
■ Down display
■ Output operation mode
INHIBIT
RESET
INHIBIT
RESET
Power Supply
Power Supply
INHIBIT
RESET
INHIBIT
RESET
Power Supply
Power Supply
Power
Reset Input
Power Reset
Inhibit Input
Setting Value
Digit Display
Control Output
Out Display
0
Power
Power Reset
Reset Input
Power Reset
Inhibit Input
Setting Value
Setting Value
Digit Display
Digit Display
Control Output
Control Output
Out Display
0
0
Power Reset
Setting Value
Digit Display
Control Output
0
TIME UP
TIME UP
No Digit Display
No Digit Display
Power
Reset Input
Power Reset
Inhibit Input
Setting Value
Digit Display
Control Output
Out Display
0
Power
Power Reset
Reset Input
Power Reset
Inhibit Input
Setting Value
Setting Value
Digit Display
Digit Display
Control Output
Control Output
Out Display
0
0
Power Reset
Setting Value
Digit Display
Control Output
0
TIME UP
TIME UP
No Digit Display
No Digit Display
Power
Reset Input
Power Reset
Inhibit Input
Setting Value
Digit Display
Control Output
Out Display
0
Power
Power Reset
Reset Input
Power Reset
Inhibit Input
Setting Value
Setting Value
Digit Display
Digit Display
Control Output
Control Output
Out Display
0
0
Power Reset
Setting Value
Digit Display
Control Output
0
TIME UP
TIME UP
No Digit Display
No Digit Display
Power
Reset Input
Power Reset
Inhibit Input
Setting Value
Digit Display
Control Output
Out Display
0
Power
Power Reset
Reset Input
Power Reset
Inhibit Input
Setting Value
Setting Value
Digit Display
Digit Display
Control Output
Control Output
Out Display
0
0
Power Reset
Setting Value
Digit Display
Control Output
0
TIME UP
TIME UP
No Digit Display
No Digit Display