HAIKU WALL CONTROL INSTALLATION
WARNING: Disconnect power to the wall control location before installing or
servicing the wall control!
WARNING: A licensed electrician must install the wall control if required by
your local electrical code.
CAUTION: Do not install the wall control outdoors or in a location where it may
come into contact with water.
A readily accessible disconnect device shall be incorporated external to the
equipment.
Verify minimum wiring compartment size required in accordance to local
electrical codes.
Ground screw is not intended for conductors larger than 10 AWG (5.3 mm
2
).
Do not use above 2,000 m (6,561 ft) above sea level.
Safe for use in non-tropical climate conditions.
READ AND SAVE THESE INSTRUCTIONS
!
!
!
Mount the wall control to the outlet box so that the word TOP is oriented
upward. Do not overtighten the screws.
Install a wallplate using the screws provided with the wallplate.
A wallplate may not be supplied with your wall control. Haiku Home
recommends using a plastic Decora-style wallplate. Metal wallplates
may interfere with Wi-Fi signals.
Turn on power to the wall control and Haiku product locations.
Follow the steps in the Quick Setup guide provided with the wall control
to set up the Haiku Home app. For detailed setup instructions, visit
resources.haikuhome.com/help
Test fan speed and light brightness using the wall control. Press the
areas between the
+
and
–
buttons to turn your products on and off.
Be
careful not to touch the sensor.
The wall control button functions vary
depending on the types of Haiku products you are controlling.
For wall control operation and troubleshooting information, visit
resources.haikuhome.com/help
Wire Color Chart
AC Hot (L1)
Black
AC Neutral (L2/N)
White*
Earth/PE
North America
100–120 V
Black
White
Green or Bare
Copper
Australia
240 V
Brown or Red
Black or Light
Blue
Green with Yellow
Tracer
All other regions
Brown
Blue
* Neutral wire (white) on wall control is labeled “N”
Revision F
09/27/17
©2017 Haiku Home. The information contained in this document is subject to change without notice.
May be protected by one or more patents listed at www.bigasssolutions.com/patents
Haiku is a trademark of Delta T Corporation, registered in the U.S. and/or other countries.
www.haikuhome.com/warranties
!
Tools Needed
• Phillips and Flat Head Screwdrivers
• Wire Strippers
!
≤
≤
2000
2000
m
m
!
1.
Wallplates are not supplied with most wall controls. Haiku
®
Home recommends
using a plastic Decora
®
-style wallplate. Metal wallplates may interfere with
Wi-Fi signals.
2.
Pre-attached to wall control
3.
L Series fans only. One module is required for each fan connected to the wall
control. See the installation guide provided with the L Series fan for instructions.
HKU-INST-78-MUL-01
Conforms to UL STD 60950-1
Certified to CSA STD C22.2 No. 60950-1
5004870
Wall Control
Wallplate
(not supplied)
Outlet box
(in wall)
Single gang outlet box shown. Your outlet box may differ.
[A]
Ground
screw
Jumper wire
(optional)
Sensor
(do not touch)
Before Installing the Wall Control
☐ Install your Haiku
®
products according to their installation guides.
☐ Contact a licensed electrician if you are uncomfortable performing
electrical work or if legally required in your area.
☐ Check your home Wi-Fi signal strength at the wall control location. Two or
more bars are recommended.
Parts and Hardware
• Wall Control
1
• (2) #6-32 x 3/4” Screws
2
• Wi-Fi Module
3
Disconnect Power
Disconnect power to all circuits wired to the outlet box at the fuse or
circuit breaker before installing the wall control!
Circuit breakers
Fuse panel
or
Prepare Outlet Box
Remove the switch from the outlet box.
Make sure the outlet box contains a neutral wire. See step 3 below for
a wire color chart. Neutral wires may be hidden or tucked into the back
of the outlet box.
If there is not a neutral wire in the outlet box, the wall
control is not compatible.
Make sure 0.5” (11 mm) of insulation is stripped from each supply wire
[A]
.
Wire Wall Control
Lift the levers on the wall control wire connectors. Push the supply
Hot wire and the Haiku product Load/Hot wire into the wall control
Hot (black) connector
[A]
. Push the supply Neutral wire and the Haiku
product Neutral wire into the wall control Neutral (white) connector
[A]
.
Close the levers and visually verify the connections.
• If you need to insert more than two wires into a connector:
Secure a jumper wire to the extra supply wiring with a wire nut or
connector that complies with local code [B]. Insert the loose end of
the jumper wire into the connector.
Attach the supply Earth/PE wire to the green ground screw on the back
of the wall control
[C]
.
Load/Hot
to Haiku
product
Hot
Neutral
Earth/PE
Neutral to
Haiku product
resources.haikuhome.com/help
Contact a licensed electrician if you are uncomfortable performing
electrical work or if legally required in your area.
2
Neutral wire
(required)
1
[C]
[B]
Mount Wall Control
Test Wall Control
resources.haikuhome.com/help
1
3
4
5
Press between
+
and
–
buttons
to turn products
on and off
0.5” (11 mm)
[A]
2
3
1
2
1
2
1
2
3
