1
6E 6129.c
6E 6129.c
on
off
ON
OFF
enter
reset
prog
auto
manu
EG110
§
1 channel time switch -
daily cycle.
User instruction
™
EG110
3 4 5 6
2
1
L
N
Technical specifications :
Electrical characteristics :
- supply voltage : 230V +10/-15% 50Hz
- output : 1 changeover contact
μ 16A - 250V AC1.
μ 3A - 250V cos
φ
= 0,6
1000 W incandescent lighting
- power consumption : 1 VA
- protection degree : IP20
- insulation class : II
Functional characteristics :
- accuracy : ± 1sec. / day at 20 °C
- operating reserve : lithium battery,
total of three years.
Environment :
Operating temperature : -10 to +50 °C
Storage temperature :
-10 to +50 °C
Connection tunnel terminals :
flexible : 0,5 to 2.5 mm
2
rigid : 0,5 to 4 mm
2
Dimensions : 3 modules (3x17,5mm)
Electrical connections :
1. Move mode selector to “
manu
”.
2. Select the state of the output with key
“
on/off
”.
3. Input with key “
+
” and “
-
” the override
duration : from 1 to 23 hours by steps of
1 hour.
Then from 1 to 27 days by steps of 1 day.
4. Move mode selector to “
auto
”.
The state indication is flashing. This means a
timed override. Return to the initial program
after the duration.
To reset the time switch :
Press “
reset
“ to clear the program.
1. Move mode selector to “
manu
”.
2. Press key “
-
” or “
+
” until display -h.
3. Move mode selector to “
auto
” to switch
back to automatic mode.
Timed override :
enter
reset
on
off
prog
auto
manu
ON
enter
reset
on
off
prog
auto
manu
ON
A warranty period of 24 months is offered on hager products,
from date of manufacture, relating to any material of manufac-
turing defect. If any product is found to be defective it must be
returned via the installer and supplier (wholesaler). The warranty
is withdrawn if :
- after inspection by hager quality control dept the device is
found to have been installed in a manner which is contrary to
IEE wiring regulations and accepted practice within the industry at
the time of installation.
- the procedure for the return of goods has not been followed.
Explanation of defect must be included when returning goods.
Warranty
GB
Working principle :
The EG110 is a time switch for the automatic
control of electrical loads.
It is fully programmable with a maximum of 20
program steps.
The front cover is sealable preventing
unauthorised access after completion of
programming.
Warning :
at the beginning of use, please
reset the device in order to clear the memory
before programming.
This is achieved by using a pen to push the
reset button.
Presentation :
Display :
time
circuit status (ON or OFF)
Buttons :
Mode selector : to select one of the
following modes :
time setting
prog
programming
auto
running mode
manu
manual override
“
on/off
” : chooses whether the circuit
is on or off
“
+
” and “
-
” : changes settings
“
enter
” : to confirm
“
reset
”
Time setting :
1. Move mode selector to
2. Input time with buttons “
+
” and “
-
”.
Important :
The clock starts when leaving the time setting mode.
Programming :
1. Move mode selector to “
prog
”.
2. Input the switching time with buttons “
+
” and “
-
”.
3. Input the type of switching with button “
on/off
”
(for the first action ON is automatically proposed).
4. Enter this program step with button “
enter
”.
Program additional time settings by repeating
steps 2 to 4.
Important :
To activate the program, move mode selector to
“
auto
”.
Running mode Auto
This mode is the current displaying mode.
It does not allow any modification.
Move mode selector to “
auto
”.
Display of the time and the state of the channel.
To check your program :
1. Move mode selector to “
prog
”.
2. Press the “
enter
” key repeatedly to display
the different program steps (switching time
and state of the channel ON or OFF).
To override the output :
Permanent override :
1. Move mode selector to “
manu
”.
2. Select the state of the output with key
“
on/off
”.
To switch back to automatic mode, move
mode selector to “
auto
”.
5
1
3
2
4
6
7
enter
reset
on
off
prog
auto
manu
OFF
enter
reset
on
off
prog
auto
manu
To modify or delete a program step :
1. Move mode selector to “
prog
”.
2. Press “
enter
” repeatedly and select the
program step to modify or to delete.
3. Modify :
- switching time with keys “
+
” or “
-
”
- state of the channel with key “
on/off
”.
To delete a program step, modify switching
time with keys “
+
” and “
-
”, until display --:--
(between 23:59 and 00:00).
4. Confirm with the “
enter
” key.
enter
reset
on
off
prog
auto
manu
ON
enter
reset
on
off
prog
auto
manu
ON
enter
reset
on
off
prog
auto
manu
ON
To cancel the timed override :
http://waterheatertimer.org/Hagar-timers-and-manuals.html
_________________________________________________________________________
