background image

Item No.: 237.56.350

Mounting Instructions

StealthLock Battery Powered RF Cabinet Lock

StealthLock is an innovative solution for keyless invisible security. Using radio frequency technology,

StealthLock allows you to secure almost any wood cabinet door or drawer with little or no changes to

the cabinet design.

StealthLock is battery operated and works with a user established 4 to 8 digit code. Operation is simple:

input your code and press lock or unlock. The Latch can operate any Receiver Latch within a 15 foot

range which allows it to be placed anywhere, leaving no trace of visible hardware. In addition, the

Latch can operate multiple Receiver Latches to secure an entire room or bank of cabinets.

StealthLock is designed to install and program easily and offers:

• Programmable user and supervisor codes

• Programmable modes of operation

• Programmable reset features

StealthLock is recommended for use on cabinets made from:

• Wood

• Wood products

• Phenolic resin

• Glass

StealthLock is NOT intended for:

• Metal furnishings or cabinets

• Mobile carts

• Exterior furnishings or cabinets

• Applications where temperatures fall below 50° F or above 120° F

StealthLock may be used in households to help protect children from unsafe materials. It is strongly

recommended that all batteries used by the StealthLock be replaced on an annual basis. Please mark

this date on your calendars to insure replacement. StealthLock has been developed to exceed the

ANSI/BIFMA 50 lb. strength requirement. In the event you have allowed the batteries to die, you

will need to forcefully enter the cabinet. The StealthLock strike plate is designed to shear away at

60 lbs. of force. A new strike plate will then be needed to operate the lock.

Содержание StealthLock 237.56.350











Отзывы: