background image

Supplied By www.heating spares.co  Tel. 0161 620 6677

PLEASE LEAVE THESE INSTRUCTIONS IN THE POCKET PROVIDED ON 

THE BACK OF THE FRONT PANEL

DESIGN, INSTALLATION AND 

SERVICING INSTRUCTIONS

SAFETY

1.  The Gas Safety (Installation and use) Regulations 1998

“In  your  own  interest,  and  that  of  safety,  it  is  law  that  all  gas  appliances  are 
installed by competent persons, in accordance with the above regulations. Failure 
to install appliances correctly could lead to prosecution.”

2.  Control of Substances Harmful to Health
 

When working with insulation materials, avoid inhalation as it may be harmful to 
health, avoid contact with skin, eyes, nose and throat. Use disposable protection. 
Dampen the material and ensure that the area is well ventilated.

3.  INSTRUCTIONS
•  Read these Instructions before installing or ligh

ting the appliance

  Leave these instructions and the ‘Benchmark’ Log Book in the pocket 

provided on the back of the appliance front panel.

Gulf

Stream

A - C L A S S

A Condensing Primary Storage Appliance

for Hot Water Supply and Central Heating

Model Ref

Sedbuk

Band

Maximum Space

Heating Load (kW)

Gas Council

No.

Heating System Type

GS

A-CLASS

 12/OV

A

10.0

Open vented heating system

GS

A-CLASS

 12/SS

A

10.0

Sealed heating system

GS

A-CLASS

 20/OV

A

18.0

Open vented heating system

GS

A-CLASS

 20/SS

A

18.0

Sealed heating system

GS

A-CLASS

 30/OV

B

26.0

Open vented heating system

GS

A-CLASS

 30/SS

B

26.0

Sealed heating system

All models are WRAS approved and listed.

MODELS

These  instructions  cover  the  following  models  and  only  apply  to  the 
appliances sold and installed in Great Britain (GB) and Ireland (IE). These 
appliances  have  been  certified  for  safety  and  therefore  it  is  important 
these instructions must be followed. The appliance and the installation 
specifications of the appliances must not be modified unless recommended 
and approved by Gledhill Water Storage Limited. 

APPLIANCE TYPE 

•  This is a Floor Mounted Fan Assisted Balanced Flue Gas Condensing Combination 

appliance for hot water supply and central heating. 

•  This appliance is for use with Natural Gas (G20) only at 20mbar.
•  This appliance for use in GB & IE only
•  Appliance category: 

I

2H

• 

Appliance types: 

C

13

, C

53

, C

33

Summary of Contents for GS A-Class 12/OV













































Reviews: