GTO SW-4000XL Installation Manual Download

Page: 1 / 44

2007 GTO, Inc.

R4200XL INST

v - 09/13/07

WARNING!

This equipment is similar to other gate or door equipment and meets or exceeds

Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has

hazards associated with its use and therefore by installing this product the installer

and user accept full responsibility for following and noting the installation and

safety instructions. Failure to follow installation and safety instructions can result

in hazards developing due to improper assembly. You agree to properly install this

product and that if you fail to do so GTO, Inc. shall in no event be liable for direct,

indirect, incidental, special or consequential damages or loss of profits whether

based in contract tort or any other legal theory during the course of the warranty

or at any time thereafter. The installer and/or user agree to assume responsibility

for all liability and use of this product releasing GTO, Inc. from any and all

liability. If you are not in agreement with this disclaimer or do not feel capable

of properly following all installation and safety instructions you may return this

product for full replacement value.

READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before

attempting to install and use this automatic gate operator. This gate operator

produces a high level of force. Stay clear of the unit while it is operating and

exercise caution at all times.

All automatic gate operators are intended for use on vehicular gates only.

This product meets and exceeds the requirements of UL 325, the standard which regulates gate operator safety,

as established and made effective March 1, 2000, by Underwriters Laboratories Inc.

Installation Manual

for installing the GTO/PRO SW-4200XL with the

GTO/PRO SW-4000XL in a dual application

FOR PROFESSIONAL INSTALLATION ONLY!

DC-SERIES

For more information on GTO/PRO’s full line of automatic gate openers and access controls visit our website at www.gtopro.com

Summary of Contents for SW-4000XL













































Search results

Summary of Contents for SW-4000XL

Reviews:

Related manuals for SW-4000XL

Brands by name

Popular brands

GTO SW-4000XL, Installation Manual

Search results

Summary of Contents for SW-4000XL

Reviews:

Related manuals for SW-4000XL

Brands by name

Popular brands