Graco True Airless LTS15 Скачать руководство пользователя

Страница: 1 / 56

3A3529C

FIRE AND EXPLOSION HAZARD

LTS 15/LTS 17 Models:

•

Use only non-flammable or water-based materials, or non-flammable paint thinners. Do not use

materials having flash points lower than 100° F (38° C). This includes, but is not limited to, acetone,

xylene, toluene, or naphtha. For more information about your material, request Safety Data Sheet

(SDS) from the supplier.

•

Spraying flammable or combustible materials in a factory or fixed location must comply with NFPA

33 and OSHA 1910.94(c) requirements in the USA and with all similar local regulations in other

countries.

Not approved for use in explosive atmospheres or hazardous locations.

For portable airless spraying of architectural paints and coatings.

Important Safety Instructions

Read all warnings and instructions in this manual, related manuals, and on the unit.

Be familiar with the controls and the proper usage of the equipment. Save these

instructions.

Содержание True Airless LTS15

























































Результаты поиска

Содержание True Airless LTS15

Отзывы:

Похожие инструкции для True Airless LTS15

Бренды по названию

Популярные бренды

Graco True Airless LTS15, Руководство пользователя

Результаты поиска

Содержание True Airless LTS15

Отзывы:

Похожие инструкции для True Airless LTS15

Бренды по названию

Популярные бренды