Grace GMQ Pro Manual Download

Page: 1 / 31

The GMQ Pro

Home Machine Quilting

System

Equipped with the Professional Series Rails

Parts List

Part List A ..............................................................................................................................2

Part List B ..............................................................................................................................3

Part List C ..............................................................................................................................4

Care of Your Frame ................................................................................................................6

Assembly Steps:

Step 1: Leveling Foot Assembly ...........................................................................................7

Step 2: Outer Leg Brace “A” Assembly ...............................................................................8

Step 3: Side Leg Brace “B” Assembly ..................................................................................9

Step 4: Table Assembly .........................................................................................................10

Step 5: Middle Leg Spacer Assembly ...................................................................................12

Step 6: Table Splice to Table Assembly ................................................................................13

Step 7: Frame End Hardware Assembly ...............................................................................14

Step 8: Track Installation ......................................................................................................14

Step 9: Frame End Assembly to Table Assembly .................................................................15

Step 10: Side Leg to Table Assembly ...................................................................................15

Step 11: Middle Leg Installation ...........................................................................................16

Step 12: Middle Leg Assembly .............................................................................................17

Step 13: Take Up Sides Assembly ........................................................................................18

Step 14: Take Up Sides to Table Assembly ..........................................................................18

Step 15: Take Up Rail Mount End Assembly .......................................................................19

Step 16: Take Up Rail Mount End to Table Assembly .........................................................19

Step 17: Three Rail Side to Table Assembly .........................................................................20

Step 18: Pivot End to Fabric Layer Rail Mount End ............................................................20

Step 19: Pivot End/ Fabric Layer Rail Mount End to Table Assembly ................................21

Step 20: Batting Rail Mount End Assembly .........................................................................21

Step 21: Batting Rail Mount End to Table Assembly ...........................................................22

Step 22: Rail Assembly .........................................................................................................22

Step 23: Rails to Frame Assembly ........................................................................................24

Step 24: Ratchet Stop Assembly ...........................................................................................25

Step 25: Carriage Stop Assembly .........................................................................................26

Fabric Installation

................................................................................................................27

Making Cloth Leaders ............................................................................................................28

Installing Your Fabric Layers to the Rails .............................................................................29

Step 1: Quilt Backing to Second Rail ...................................................................................29

Step 2: Quilt Top to 3rd Rail .................................................................................................29

Step 3: Batting.......................................................................................................................29

Step 4: Attaching Layers to the Take-Up Rail ......................................................................30

Step 5: Putting Your Machine/ Carriage onto Frame ............................................................30

Rolling Your Fabric ................................................................................................................31

The Four-Inch Principle .........................................................................................................31

Bungee Clamp Assembly .......................................................................................................31

Jim M. Bagley, GraceWood, Inc

(Reproduction Prohibited)

Print Date 02-01-2010

Summary of Contents for GMQ Pro
































Search results

Summary of Contents for GMQ Pro

Reviews:

Related manuals for GMQ Pro

Brands by name

Popular brands

Grace GMQ Pro, Manual

Search results

Summary of Contents for GMQ Pro

Reviews:

Related manuals for GMQ Pro

Brands by name

Popular brands