background image

1

Quilting With The Grace NM-EZ3

TM

Quilting Frame

Table Of Contents                                      

Helpful Information...........................................................................x
Care, Finishing And Storage............................................................ x
Warranty........................................................................................... x
Parts List........................................................................................... x
Assembly...........................................................................................

1

Before You Begin.................................................................. 1
Step 1 Install Hardware To Diagonal Stand........................

1

Step 2 Install Hardware To Pivot Section.............................

1

Step 3 Install Hardware To Mounting Ends.........................

2

Step 4 Base Feet To Diagonal Stand.................................... 2
Step 5 Pivot Sections to Diagonal......................................... 2
Step 6 Ratchet Wheels to Poles........................................... 3
Step 7 Assembling the Frame in Different Sizes................... 3
Step 8 

Ratchet Stops and Poles with Wheels to Mounting Ends

4

Step 9 Brace Assembly........................................................ 

5

Step 10 Pole/End Assembly To Leg/Stand/Pivot Assembly 5

Folding The EZ3

TM

............................................................................

6

Tilting The EZ3

TM

.............................................................................. 7

Quilting Instructions......................................................................... 7

Preparing The Fabric Layers For Installation.....................7

Installing The Quilt

 

Fabrics..................................................7

Trouble Shooting....................................................................9
Tying Quilts...........................................................................10

Making And Using Cloth Leaders.....................................................10

Copyright November 2000 Jim M. Bagley
GraceWood, Inc.   Reproduction Prohibited,
Patent Pending

Summary of Contents for NM-EZ3

















Reviews: