background image

OPERATING & 

MAINTENANCE

INSTRUCTIONS

GO 68HD • GO 68 • GO 62HD SERIES

GO 50 • GO 380 / 250 • GO 15 SERIES

SEWER & DRAIN CLEANING MACHINES &

POWER CABLE FEEDERS

“The Drain Cleaning Machine & Equipment Specialist”

GORLITZ      INC.

“The Drain Cleaning Machine & Equipment Specialist”

“The Drain Cleaning Machine & Equipment Specialist”

“The Drain Cleaning Machine & Equipment Specialist”

“The Drain Cleaning Machine & Equipment Specialist”

GORLITZ      INC.

“The Drain Cleaning Machine & Equipment Specialist”

“The Drain Cleaning Machine & Equipment Specialist”

“The Drain Cleaning Machine & Equipment Specialist”

HOW TO ORDER

PRICES

SALES TAX

FREIGHT POLICY

MERCHANDISE CLAIMS AND RETURN POLICY

GORLITZ LIMITED WARRANTY

MANUFACTURERS WARRANTIES AND LITERATURE

In order to avoid mistakes or delays of your shipment, please refer to our part number and description.

Since prices are subject to change we cannot guarantee them for more than 30 days. The prices listed are valid for the period

indicated on the cover of the price list only. Prices are Net F.O.B. Factory, Santa Fe Springs, California.

Gorlitz Sewer & Drain, Inc. is required to charge applicable State Sales Tax on every item sold unless a California State Sales

Tax Exemption Certificate has been provided.

All merchandise shipped per parcel service are prepaid and added to the invoice. All shipping fees per trucking lines are the

responsibility of the customer. If any freight damages or losses are experienced, Gorlitz Sewer & Drain, Inc. requests that the

freight company carrying the merchandise be contacted by the customer for freight claims.

All discrepancies in goods received must be claimed within five days after receipt of goods. Any item to be returned must be

referenced by invoice number, date of sale and written consent of seller.

All products manufactured at Gorlitz Sewer & Drain, Inc. are warranted to be free from defects in material and workmanship

under normal use and maintenance for a period of one (1) year from date of purchase to original buyer. If any parts break or

fail, we ask you to notify your nearest dealer or Gorlitz Sewer & Drain, Inc. and supply us with proof of purchase and nature of

failure. Gorlitz will repair or replace (at our option) any parts found to be defective. The replacement part assumes the

unused portion of the warranty. Transportation of the product to any service station is the responsibility of the user unless

stated otherwise in this warranty.

This warranty does not apply to expendable items (Cables, Knives, Nozzles, Hoses, Fittings, etc.) and damage due to

negligence, unauthorized repair or alteration, chemicals, misuse or accidents. Adjustments of any kind can not be made on

shaved, kinked or broken hoses and kinked or broken cables because it shows evidence of abuse or to much pressure.

This warranty is exclusive and in lieu of all other expressed warranties and Gorlitz Sewer & Drain, Inc. does not authorize any

part to assume for it any other obligation or liability. In no event shall Gorlitz Sewer & Drain, Inc. be liable for special or

consequential damages arising from the use of this product or for any delay in the performance of this warranty due to causes

beyond our control.

In placing this order Buyer expressly understands, acknowledges and agrees that: (1) Buyer has received and read the

Operating and Maintenance Instructions that accompanied this equipment order, including Gorlitz’s Limited Warranty and all

of the other Terms and Conditions of doing business with Gorlitz Sewer & Drain, Inc. (“Gorlitz”) as stated therein; (2) Buyer will

operate and maintain the equipment in accordance with the specifications stated in the Instructions; (3) Buyer indemnifies

and holds Gorlitz harmless for Buyer’s failure to use the equipment in accordance with the specifications stated in the

Instructions; (4) the equipment is being sold to Buyer on an “as is” and “where is” basis and that except as specifically set forth

in this agreement, Gorlitz makes no other representations or warranties, whether express or implied; and (5) all disputes

arising under this agreement shall be submitted to courts of competent jurisdiction in the State of California and the prevailing

party in any action or proceeding to enforce any provision of this agreement will be awarded reasonable attorney fees and

costs incurred in that action or proceeding or in efforts to negotiate the matter.

Most products used on our equipment are warranted to the final consumer by their manufacturers. Copies of such warranties

are supplied with our products or are available from the manufacturers. As a service, Gorlitz Sewer & Drain, Inc. will obtain

copies of consumer warranties from the warrantor and will furnish them free of charge to consumers upon request. Gorlitz

Sewer & Drain, Inc. assumes no responsibility for the content of such warranties or sales literature by performing this service.

Summary of Contents for GO 15 Series





























Reviews: