2
2
LIVE
NEUTRAL
GROUND
BLACK
WHITE
RED
FF
x1
Wall plate
Plaque murale
Placa de pared
Model / Model / Modelo #:
SE1303-WH3-00LFW-G, SE1303-BP2-00LFW-G
OUTDOOR LED SMART SECURITY LIGHT
(Page 1)
LAMPE DE SÉCURITÉ INTELLIGENTE À DEL POUR L’EXTÉRIEUR
(Page 3)
LUZ DE SEGURIDAD LED INTELIGENTE PARA EXTERIORES
(Página 6)
Diffuser
Diffuseur
Difusor
Required/
Nécessaire/
Se necesita
* Actual hardware may differ from illustration/ * Les éléments de fixation réels peuvent être différents de ceux de l’illustration./ * Es posible que los herrajes reales difieran de los de la ilustración.
INSTALLATION FOR ROUND SURFACE
MOUNT ELECTRICAL BOXES
INSTALLATION FOR RECESSED
ELECTRICAL BOXES
x2
AA/BB
DD x1
EE x1
GND
FRON
T
x2
AA/BB
DD x1
GND
FRON
T
GND
FRON
T
GND
FRON
T
1 RECESSED
1 SURFACE
Pull supply wires out of the junction box (j-box). With the side marked “FRONT” facing out, attach the mounting strap
(DD)
to the j-box with
machine screws (
AA
or
BB)
. Remove the protective liner from adhesive side of the gasket
(EE)
. Guide the j-box wires through the gasket
opening. Aligning the center holes of the gasket and mounting strap and apply the gasket to the outer edge of round edge of the j-box.
Pull supply wires out of the junction box (j-box). With the side marked “FRONT” facing out, attach the mounting strap (
DD)
to the j-box with
machine screws
(AA or BB)
.
Motion Sensor (PIR) Head
Tête du détecteur de mouvement
passif à infrarouge (PIR)
Cabeza del sensor de movimiento (PIR)
Pairing Button
Bouton d’appariement
Botón de emparejamiento
Lower Motion Sensor
Détecteur de mouvement inférieur
Sensor de movimiento inferior
Light head
Tête de la lampe
Cabeza de luz
SHUT OFF POWER AT THE CIRCUIT BREAKER OR FUSE PANEL BEFORE REMOVING
THE OLD FIXTURE OR INSTALLING THE NEW ONE.
ENGLISH
WARNINGS AND CAUTIONS
HOW TO CHOOSE A LOCATION SITE
IMPORTANT!! READ BEFORE YOU BEGIN!
Select a location that allows the sensor to perform to its highest level.
The fixture can be mounted three distinct ways:
WALL MOUNT
,
EAVE MOUNT
or
BOX
MOUNT
.
This security light uses passive infrared (PIR) technology to automatically turn on the light.
Passive infrared does not detect motion, but sensing differences in ambient temperatures,
versus warmer objects in its field of view. As such, the sensor can be set off by a variety of
other sources, including dryer vents, hot tubs, and the like. The PIR sensor cannot detect
motion through plexiglass or glass barriers. Select an installation location carefully. Do not
aim the PIR towards areas having frequent pedestrian or motorized traffic, and/or other
objects that generate areas of warmer air. All of these may trigger the motion sensor security
light and maybe disruptive to the intended operation of the light.
Do
NOT
install near other sources of light, which can fool the built-in light sensor into thinking
it is daylight, and may prevent the proper operation of the light.
3
4
3
2
1
READ ENTIRE INSTALLATION PROCEDURE BEFORE YOU BEGIN!
1. This fixture can only be installed over a recessed electrical box,
OR
a UL Listed
surface mount electrical box rated for wet locations. Surface mount electrical
boxes require the use of the foam gasket (included), to prevent water seeping into
the electrical box.
2. Do not look directly at LEDs for extended period of time. Can cause eye damage.
3. LEDs can be damaged by electrostatic discharge shock. Before installation,
discharge yourself by touching a grounded bare metal surface to remove this
hazard.
1 SURFACE
1 RECESSED
WALL MOUNT EAVE MOUNT BOX MOUNT
INSTALLATION
SHUT OFF POWER BEFORE REMOVING OR INSTALLING ANY FIXTURE.
The fixture can be mounted to a round surface mount or a recessed electrical box.
WARNING!
Recommended Mounting Height: 7-15 ft.
Minimum Mounting Height: 7 ft.
NOTE:
Mounting the fixture above the 7-15 ft. range
can result in a decrease in the sensor detection range.
1
GND
FRONT
CC
x1
AA
x2
BB
x2
EE
x1
FF
x1
DD
x1
4. Minimum 90°C supply conductors. For fixture electrical ratings, see fixture label.
5. If unsure if the electrical box is properly grounded, or the box is plastic and has
no ground wire, or are unfamiliar with the methods of properly grounding fixture,
consult a qualified electrician.
6. Do
NOT
use this fixture with dimmers.
7. Fixture will reliably operate between temperatures from -20°F to 122°F.
(At temperatures above 92°F, the PIR may not detect body heat.)
Push the ends of the house wires from the J-box into the contact holes of
the electrical disconnect-plug from the hardware kit
(FF)
, carefully match
the color of the black and white wires corresponding to the color coded
surface of the connector. Insert the house ground wire into the hole marked
by the red surface. Verify the wires are secure.
Electrical disconnect plug
Fiche de déconnexion électrique
Enchufe de desconexión eléctrica
Hardware kit* / Kit de petit
matériel de fixation*/
Kit de aditamentos*
