![background image](http://html.mh-extra.com/html/giant-electronics/t6500/t6500_alignment-procedure_2221800001.webp)
THE CONTENT OF THIS DOCUMENT IS GIANT ELCT.LTD. INTELLECTUAL PROPERTY AND IS THE
PROPERTY OF GIANT, IT IS TO BE TREATED AS STRICTLY AND IS NOT BE DISCLOSED,
REPRODUCED, OR USED EXCEPT AS AUTHORIZED IN WRITING BY GIANT ELECTRONIC LTD. IN
CONNECTION WITH THE MANUFACTURE,MAINTENANCE AND USE OF THE GIANT EQUIPMENT
WHICH IT PERTAINS. COPYRIGHT @GIANT ELECT. LTD, ALL RIGHTS RESERVED.
GIANT ELECTRONICS LTD.
Title: Alignment Procedure
Model: T6500
A. PCB LEVEL (Test Condition: under CH15)
NO ITEM
ALIGNMENT
METHOD
REMARK
1.
LCD display
(Should enter test
mode)
1. Press and hold the ‘+’ key and ‘Menu’ key together.
2. Turn on the radio power until a good key chirp is heard,
and the backlight is on for about 500 ms . finally, the
LCD should be display ‘
1
CH
’.
3. Press ‘DOWN’ key , then all LCD segments should be
anticlockwise displayed.
4. Finally, all the LCD segments should be shown for
about 500ms as follows: 2
18
88.
.
2.
Standby current
1. Set A-METER, and RX mode.
2. Check the standby current <45mA DC.
3.
Talk on current
1. Set A-METER, and TX mode @50ohm load.
2. Check the talk on current <900mA DC.
3. Set channel to 14
4. Check the talk on current <500mA DC.
4.
VCO
1. Set RX or TX mode
2. Check TP503 to provide 0.7~2.3VDC .
3. Adjust L509 to provide 2.2
±
0.1
VDC at TP503 if VCO
level are more than 2.4VDC on CH14.
4. Set WX mode, check TP504 to provide 0.7~2.4VDC(for
T5950)
5. TX Power 1. Set TX mode CH15, Check transmit power to provide
<GMRS
2. Set TX mode CH14, Adjust VR503 to provide
<FRS
6.
TX Frequency
1. Set TX mode
2. Adjust VC501 to provide 462.5500MHz
±
50Hz.
7. CTCSS
Tone
Frequency
1. Set CH15/CODE1 and Tx mode.
2. Check CTCSS tone frequency to be within 66.8Hz to
67.2Hz.
8.
CDCSS Frequency
1. Set TX mode
2. Set CH15/CODE99
3. Adjust VR501 to provide 503 Octal Code
4. Set CH15/CODE39, check Octal Code to be 023
FILTER SET:
1.Input Level:
0.9KHz
9.
CTCSS Tone Dev.
1. Set CH15/CODE1
AF input level to off, check DEV to
be 300Hz~ 650Hz.
2. Set CH14/CODE38
AF input level to off, check DEV
to be 300Hz~ 650Hz.
FILTER SET:
1.50HZ~300HZ
2.750
µ
s De-emp
ON
3. PK+
4. FM DEV.
AVG ON
10. TX
Modulation
& distortion
1.Set AF level at 50mv;1KHz,Adjust VR101 to provide
Max TX deviation 2.25KHz to 2.35KHz.
2.Check input Mic level in 5~15 mV to provide normal
deviation 1.5KHz.
3.Check the demodulation distortion <= 5%.
5. Audio Frequency Response.
a) Input a 2.0mV 1KHz audio frequency to TP116
and press ‘PTT’ switch.
b) Check the response compare to 1KHz tone.
i) 500Hz : -5.0 dB to –11.0 dB.
ii) 2.5KHz : +3.0 dB to +9.0 dB .
FILTER SET:
1.HPF 50Hz
2.LPF 15KHz
3. PK +