background image

1

To assemble the tree top, 

properly insert the "TOP" 

section into the top of 

section "B". (See Fig. D)

Adjust branch tips, as needed, 

for a fuller look.

7

Carefully unpack the carton.

Remove bubble wrap and 

inspect the sections of your tree.

The carton should include sections 

"A", "B" and "Top", as well as 

a Tree Stand.

 

2

3

The tree stand should be open and 

set at 90° angle.

90°

Insert Section A into tree stand, 

tighten the thumbscrew. Then

insert the plug into an electrical 

wall outlet.  

Nicolas Holiday Ltd. thanks you for purchasing this pre-lit Christmas

tree. Should you have any problems with your tree, visit us at

www.geholidaylighting.com

 for more information. You can call our

toll free number at 1-877-398-7337.

Check our website for latest service hours and assembly instruction videos.    

IMPORTANT: 

Store your carton neatly in a cool, dry location protected from sunlight

to prolong the tree life and to better keep the light sets in working order. Do not place 

a heavy load on the carton to avoid damage to or crushing the carton and tree inside.

NOTE:

  

No tools required 

  

7.5 FT TREE

Tree Storage

1. Remove the tree’s main extension cord 

plug from the wall outlet.

2. Starting at the top, disconnect the "TOP" 

from section "B" and then disconnect 

section "B" from section "A". 

{Fig. 1}

Note:

 Gently fold the tips in branches 

and fold the branches 

up toward the center. 

{Fig. 2}

 

Care should be taken to avoid 

damage to the lights. 

3. Remove section "A" from the tree stand 

and close tree stand to place into the carton.

4. Refer to the drawing on how to repack 

your tree. 

{Fig. 3}

DISCLAIMER : 

DO NOT USE OR INSTALL  ANY ADDITIONAL CHRISTMAS LIGHTING 

OR ORNAMENTATION THAT IS POWERED BY A LIGHT BULB SOCKET. DOING THIS 

MAY RESULT IN DAMAGE TO YOUR CHRISTMAS TREE OR CAUSE PERSONAL

INJURY. DOING THIS, WILL RESULT IN A VOID OF THE LIMITED WARRANTY OF 

THIS PRODUCT.   

Disconnect the decorative item from the power source before

performing any maintenance or cleaning. 

Troubleshooting Tips

If the tree does not illuminate, make certain the wall switch is turned on. 

If one section of your tree does not illuminate, check that section for loose 

or missing bulbs, all factory connections are properly made or that you 

properly made all the electrical connections between each tree section. 

4

Untie RED twist-tie to release branch

panels. All branches should fall into 

place with a gentle pull on the outer

layer of branches.

Fig. A. Start at the inner and stagger 

the tips. Move each tip up to 40°. 

Fig. B. Make tips 2 & 3 to horizontial, 

tip 4 to vertical and tips 5 and 6 

up to 45°. 

 

B

A

TOP

2

3

1

Thumbscrew

To assemble the section"B", 

properly insert section "B"  

into the top of section "A". 

(See Fig. C)

Adjust branch tips, as needed, 

for a fuller look.

5

Repeat “Step 4” for shaping.

6

For indoor use only    

120V

THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.

GE is a trademark of General Electric Company

and is under license by Nicolas Holiday Ltd. 

©2022 Nicolas Holiday Ltd.   

9 F., No. 37, Guangfu North Rd., Taipei, Taiwan 10560   All rights reserved.

Printed in China       

22002LO

 Tree Sections 

Tree Stand 

Approx. Asm Time*

7.5 ft tree 

Metal 

10 – 15 minutes

TREE ASSEMBLY DIAGRAM

7.5 FT

TOP

B

A

SCHEMATIC DIAGRAM

Tree Stand 

OPEN

Fig. C

Fig. D

   Pre-Lit Christmas Trees

Assembly Instructions

A

40°

1

 

B

90°

90°

45°

2

3

4

5

6

TOP

A

B

Tree Stand 

To electrically connect the sections please

refer to the Tree Assembly Diagram. Take 

the male and female connectors, locate 

the flat area on each and fully insert the 

connectors together. Fully screw on 

securing cap.

To electrically connect the top, again refer 

to the Tree Assembly Diagram taking the 

male and female connectors, aligning the 

flat areas and fully inserting together. 

Fully screw on securing cap.

Reviews: