background image

a

BFL80UQ

e

Quiet Exhaust Fan/Light 

User’s Guide

210572217 Rev. B 3-08

Item Stock Number(s): BFL80UQ

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.

PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should always be followed to reduce

the risk of fire, electric shock and injury to person, including the following:

1. Read all instructions before installing or using

exhaust fan.

2. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the
manufacturer.

3. Before servicing or cleaning the unit, switch power

off at service panel and lock the service disconnecting
means to prevent power from being switched on

SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS -

OPERATING MANUAL

accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.

4. Installation work and electrical wiring must be done

by qualified person(s) in accordance with all applicable
codes and standards, including fire-related construction.

5. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of

1 of 8

www.geelectrical.com

Summary of Contents for BFL80UQ









Reviews: