Two (2) 1/8" (3mm) pilot holes
Faceplate
WARNING
IF DRILLING IS REQUIRED, you should read and thoroughly understand steps 1 - 4 prior to
drilling.
Please drill holes from both sides to avoid splintering of the door face.
IF HOLES ARE ALREADY DRILLED IN YOUR DOOR, install latches and begin at step 5.
For questions, please call 1-877-4GATEHS, 8:30 a.m. - 5:30 p.m. EST,
Monday through Friday.
SAFETY INFORMATION
INSTALLATION AND CARE NOTATIONS:
1. The important safeguards and instructions appearing in this manual are not meant to
cover all possible conditions and situations that may occur. It must be understood that
common sense, caution and care are factors which cannot be built into any product.
These factors must be supplied by the person(s) caring for and operating the unit.
PREPARATION
Additional tools needed for NEW installation:
• Pencil
• Hammer • 2-1/8 in.(54mm) Hole Boring bit
• Chisel
• Power drill
• Tape measure • 1 in.(25mm) & 1/8 in.(3mm) Drill bits • 2 in.(51mm) 6d common nail
ITEM #0226069/0226087/0226090/0226091/0141055/0141053
0225974/0225976/0239863/0239857
BED & BATH/HALL & CLOSET
MODEL #TUT30/TUTG0/TUX230/TUX2G0/TUX730/TUX7G0
LY9X203/LY9X20G/LY9X703/LY9X70G
INSTRUCTIONS FOR INSTALLATION OF LOCKSETS
1. MARK DOOR
Use enclosed template to mark installation holes on both sides of the door as shown.
A. Heightline - 38 in. from floor (965mm).
B. Center of door thickness on heightline.
C. Knob hole center for backset - 2-3/8 in.(60mm) or 2-3/4 in.(70mm) as desired.
(Note 2-3/8 in.(60mm) is standard)
TO MARK OPPOSITE SIDE OF DOOR: fold template in opposite direction and place on other
edge of the door, matching up "mark (1B)" - center of door thickness as shown in
illustration.
(Back of template will be facing you.)
Mark knob hole center at point of template indentation (1C).
2. DRILL HOLES ( SEE ILLUSTRATIONS )
Drill 1/8 in.(3mm) pilot holes as marked in Step 1 at points (B) and (C).
A. Drill 2-1/8 in.(54mm) holes about 1/2 way through door, then finish drilling from other side,
to minimize splintering.
B. Before drilling latch holes, mark location for strike plate holes in door jamb by closing door
and inserting a 2 in.(51mm) common nail from inside 2-1/8 in.(54mm) hole in to pilot hole
so that nail makes an indentation in the jamb.
C. Open door and drill a 1 in.(25mm) latch hole in the door edge through to the 2-1/8 in.
(54mm) hole.
!
!
3. A. MORTISE FOR LATCH
Use faceplate as a pattern for mortise and pilot holes. Faceplate should fit flush.
B. lNSTALL LATCH
Install as shown. Ensure beveled edge faces door jamb.
4. PREPARE DOOR JAMB
Drill and Install strike plates
A. Mark outline for plastic dust box and then drill
33/64 in.(13mm) deep,
1-1/4 in. (32mm) height
to allow for installation of plastic dust box,
61/64 in.(24mm) wide
Mark location of strike mortise using strike plate as a template by placing plate over
dust box and chisel outline. for strike plate with 1/8 in.(3mm) deep as marked on
door jamb
B. Insert dustbox into hole, and apply strikeplate.
Secure using 0.76 in.(19mm) wood screws into pilot holes as shown.
5. TUBULAR LOCK UNIVERSAL BACKSET LATCHBOLT
( This backset is set a 2-3/8 in.(60mm). It only needs to be adjusted if your door requires
a 2-3/4 in.(70mm) backset. )
IF BACKSET ADJUSTMENT IS NECESSARY:
A. Latch is preset at factory for 2-3/8 in.(60mm) backset.
Caution: Be sure the latch cam is upright before making any backset adjustment.
B. To convert latch to 2-3/4 in.(70mm) backset, pull the rear part until 2-3/4 in.(70mm) is
completely shown in indicator.
To correct cam expand to reset and compress back to 2-3/8 in.(60mm).
Note:
• Our latches come with interchageable faceplates, allowing conversion from a radius
shape toa square shape so it will fit most doors.
Look first at your door to determine which configuration will work best in your
application and make the suitable change according to the instructions below, if
needed.
• Converting from radius corner faceplate to square corner and vice versa:
Detach installed faceplate using a flat head screw driver.
Replace with new faceplate. Align holes in the faceplate and the base plate and snap
them together.
TCD-
M0G0J12
09/12-02
A
B
C
38 in.(965mm) from finished floor
Template
Template
OR
2-1/8 in.
(54mm)
A
B
C
1 in.
(25mm)
}
(A1)
B
A
}
0.7
6 in.(
1
9mm)
(A1)
Short wood screw
2-3/4 in.(70mm)
2-3/8 in.(60mm)
Yes
No
Caution: Be sure the latch cam is upright before installing latch.
To correct, expand to 2-3/4 position to reset cam and compress back to 2-3/8 in.
Notch
Radius corner faceplate
Square corner faceplate
1-3/4 in.
(45mm)
1-3/8 in.
(35mm)
1-9/16 in.
(40mm)
Ø 2-1/8 in.(54mm)
Fold here. Place on
door edge.
Drill 1 in.(25mm)
hole at center of
door edge.
Backset 2-3/4 in.(70mm)
Backset 2-3/8 in.(60mm)
THE FOLLOWING CARE INSTRUCTIONS SHOULD BE
FOLLOWED TO INSURE A LONG LASTING FINISH:
1. Remove locks, or do not install locks, prior to painting you door.
2. Periodically clean with mild soap and a soft
cloth only.
Do not use abrasives or harsh chemicals, and
avoid sharp or scratching objects.
