![background image](http://html.mh-extra.com/html/garmin/rv-bbt602/rv-bbt602_installation-instructions_567235001.webp)
RV-BBT602
Installation Instructions
Important Safety Information
WARNING
See the
Important Safety and Product Information
guide in the
product box for product warnings and other important
information.
NOTICE
Failure to follow these cautions could result in damage to the
vehicle or poor product performance.
This device must be installed according to these instructions.
Disconnect the vehicle's power supply before beginning to install
this product.
Before applying power to this product, make sure it has been
correctly grounded according to the installation instructions.
You must read all installation instructions before beginning the
installation. If you experience difficulty during the installation,
contact Garmin
®
Product Support.
Connector Identification
Item Connector
Notes
À
Microphone input
3.5 mm mono miniplug for the hands-
free microphone (included)
Á
Video in
Composite video RCA connector
Â
Zone 1 line out
Left, right, and subwoofer RCA
connectors
Ã
Wiring harness
connectors
The wiring harnesses are not included.
See (
) for
pinout information.
Ä
Zone 2 line out
Left, right, and subwoofer RCA
connectors
Å
Aux 1 input
Left and right RCA connectors
Æ
Zone 3 line out
Left, right, and subwoofer RCA
connectors
Ç
Camera audio input or
Aux 2 input
Left and right RCA connectors
È
Zone 4 line out
Left, right, and subwoofer RCA
connectors
Item Connector
Notes
É
USB (500mA)
Reserved for manufacturer use
Compatible only with low-current
(<500 mA) USB devices
USB (2.1A)
Interfaces and charges supported
smartphones and USB devices
CAN BUS 1
Connects to an NRX wired remote
control using an adapter (sold
separately)
CAN BUS 2
Reserved for vehicle integration
Digital Audio Broadcast
(DAB) port
Connects to a compatible FUSION
®
DAB
module and antenna
AM/FM antenna
Connects to the vehicle antenna. The
included adapter may be required.
Pin Identification
You can use this pinout diagram and table to create a wiring
harness for this device.
Pin
Function
À
Speaker: zone 2 left positive (+)
Á
Speaker: zone 2 left negative (-)
Â
Speaker: zone 1 left positive (+)
Ã
Speaker: zone 1 left negative (-)
Ä
Speaker: zone 1 right positive (+)
Å
Speaker: zone 1 right negative (-)
Æ
Speaker: zone 2 right positive (+)
Ç
Speaker: zone 2 right negative (-)
È
Ignition switch positive (+12 Vdc input)
É
Power ground (-)
Amplifier signal (+12 Vdc output)
Dim
Not applicable
Power input positive (+12 Vdc input)
Backup camera (+12 Vdc to trigger)
Tel/mute (ground to trigger)
Connecting a FUSION NRX Remote Control
You can connect a FUSION NRX remote control (not included)
to the stereo dock using an adapter cable (not included). You
can purchase an NRX remote control and the required adapter
cable from your FUSION dealer.
You can connect up to three NRX remote controls directly to the
stereo dock without connecting them to an additional power
source. If you want to connect more than three NRX remote
controls to the stereo dock, you must connect them to an
additional power source. See the instructions provided with the
remote control for more information.
1
Install the NRX remote control by following the instructions
provided with the remote control.
2
Repeat the previous step for each additional NRX remote
control you want to install.
3
Route the network cable from the NRX remote control
network to the location of the stereo dock.
June 2017
190-02206-03_0A
Summary of Contents for RV-BBT602
Page 4: ......